SSAB Form 200 Hot-Rolled

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    General Product Description

    SSAB Form 200 is a mild steel intended for forming with the best conceivable properties in both drawing and stretch forming operations. SSAB Form 200 is used for a wide variety of applications including vehicle parts, refrigerators, electric radiators and water radiators.

    Dimension Range

    SSAB Form 200 is available in thicknesses of 1.80-15.00 mm and widths up to 1610 mm as coils, slit coils and as cut to length in lengths up to 16 meters.

    Mechanical Properties

    Hide/Show specific columns Edit
    Select columns to display
      Thickness
      (mmin)
      Yield strength ReH
      (max MPa)
      Tensile strength Rm
      (max MPa)
      Elongation A80
      (min %)
      Elongation A5 1)
      (min %)
      Min. inner bending radius for a 90° bend
      (x t)
      1.80 - 3.000.0709 - 0.118 300 400 33 37 0.0
      3.01 - 6.000.119 - 0.236 300 400 37 0.0
      6.01 - 15.000.237 - 0.5906 300 400 37 0.4
      Compare parameters

      Select one parameter to compare

      Comparison

        The mechanical properties are tested in the transverse direction.

        1) A5 value applies for thicknesses ≥ 3.00 mm.

        Chemical Composition (heat analysis)

        Hide/Show specific columns Edit
        Select columns to display
          C
          (max %)
          Si
          (max %)
          Mn
          (max %)
          P
          (max %)
          S
          (max %)
          Al
          (min %)
          0.06 0.03 0.35 0.030 0.025 0.015
          Compare parameters

          Select one parameter to compare

          Comparison

            The steel is grain refined.

            Tolerances

            SSAB Form is delivered with SSAB Form tolerances, with improved guarantees compared to EN 10051. More details are available at SSAB.com

            Thickness

            SSAB Form thickness tolerances correspond to EN 10051 tolerances for deep drawing steels according to EN 10111 as default value. After special agreement tighter tolerances can be delivered for certain products and dimensions.

            Length and Width

            SSAB Form tolerances for width and length are according to SSAB standard. The SSAB standard offer narrower width and length tolerances compared to EN 10051.

            For coil and sheet with mill edge, the width tolerances are corresponding to -0/+20 mm.

            For coil and sheet with cut edge, the width tolerances are corresponding to -0/+2 mm.

            After special agreement, tighter tolerances can be delivered for certain products and dimensions.

            Length tolerances only apply for cut to length sheets.

            Shape

            Tolerances according to EN 10051.

            Flatness

            SSAB Form tolerances guarantee a maximum flatness deviation of 3 mm/m in addition to the EN 10051 flatness requirements.

            Flatness guarantees only apply for cut to length sheets.

            Surface Properties

            According to EN 10163-2 Class A, Subclass 3.

            Delivery Conditions

            Thermomechanically rolled.

            Surface and edge condition

            SSAB Form 200 is available with non-pickled or pickled surface with mill or cut edge.

            Fabrication and Other Recommendations

            SSAB Form 200 has good cold forming, welding and cutting performance especially laser-cutting.

            SSAB Form 200 is suitable for hot dip galvanizing.

            For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

            Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.

            Contact Information

            www.ssab.com/contact