Duroxite® 101

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

On this page

General Product Description

Duroxite® 101 is manufactured by depositing a chromium-rich carbide overlay on Hardox 450 backing plate. The hardfacing overlay is suitable for severe abrasive wear and impact applications. With its optimum carbide concentration, consistently good wear resistance from top surface through 75% depth of overlay, and Hardox backing plate, Duroxite® 101 provides a better combination of wear and impact resistance compared to the traditional mild steel backing overlay plate.

Key Benefits

  • Designed to better withstand plastic deformation due to its high yield strength flexing back after impact
  • Stronger support due to high hardness of Hardox and better bonding between overlay and base steel
  • When overlay wears off Hardox® 450 backing plate will wear at a lower rate than mild steel providing a greater safety margin
  • Better performance for impact situations than Duroxite® 100 at elevated temperatures up to 350° C (660° F), but impact resistance is best at room temperature

Typical Applications

Duroxite® 101 is widely used in the mining, cement and power generation industries. Some specific applications include:

Hide/Show specific columns Edit
Select columns to display
    Mining Loader bucket liners, bucket lip and side shrouds, jaw shrouds
    Cement Heel pads and dewatering conveyors
    Power Coal discharger chutes
    Compare parameters

    Select one parameter to compare

    Comparison

      Mining
      Loader bucket liners, bucket lip and side shrouds, jaw shrouds
      Cement
      Heel pads and dewatering conveyors
      Power
      Coal discharger chutes

      For more information on applications see the Duroxite® Product brochure.

      Standard Dimensions

      Hide/Show specific columns Edit
      Select columns to display
        Standard overlay thicknesses
        Metric unit
        6 mm on 6 mm
        10 mm on 10 mm
        12 mm on 12 mm
        6 mm on 20 mm
        6 mm on 25 mm
        6 mm on 32 mm
        Compare parameters

        Select one parameter to compare

        Comparison

          Standard overlay thicknesses

          Metric unit
          6 mm on 6 mm
          Standard overlay thicknesses

          Metric unit
          10 mm on 10 mm
          Standard overlay thicknesses

          Metric unit
          12 mm on 12 mm
          Standard overlay thicknesses

          Metric unit
          6 mm on 20 mm
          Standard overlay thicknesses

          Metric unit
          6 mm on 25 mm
          Standard overlay thicknesses

          Metric unit
          6 mm on 32 mm

          Other plate sizes and custom thicknesses can be produced upon request.

          Standard plate sizes

          Hide/Show specific columns Edit
          Select columns to display
            Metric unit Imperial unit
            1.85 m x 2.85 m 6.1' x 9.3'
            1.2 m x 2.4 m 4' x 8'
            1.5 m x 3.0 m 5' x 10'
            1.8 m x 3.0 m 6' x 10'
            Compare parameters

            Select one parameter to compare

            Comparison

              Metric unit
              1.85 m x 2.85 m
              Imperial unit
              6.1' x 9.3'
              Metric unit
              1.2 m x 2.4 m
              Imperial unit
              4' x 8'
              Metric unit
              1.5 m x 3.0 m
              Imperial unit
              5' x 10'
              Metric unit
              1.8 m x 3.0 m
              Imperial unit
              6' x 10'

              Other plate sizes and custom thicknesses can be produced upon request.

              Mechanical Properties

              Hide/Show specific columns Edit
              Select columns to display
                Wear properties
                ASTM G65 – Procedure A weight loss 2)
                Number of overlay passes Typical surface hardness1)

                (HRC)
                Typical surface hardness1)

                (HV)
                Surface
                (g max)
                75 % depth of overlay 3)
                (g max)
                Multiple passes 59 - 62 675 - 750 0.18 0.18
                Compare parameters

                Select one parameter to compare

                Comparison

                  1) Surface hardness is measured on machined flat surface just below overlay surface.

                  2) ASTM G65 - Procedure A weight loss, is a standard test measuring sliding abrasion resistance using a dry sand/rubber wheel apparatus. ASTM G65-Procedure A is the most severe test method.

                  3) ASTM G65 - Procedure A weight loss, wear test is conducted at 75% depth of the overlay materials to ensure consistently good wear resistance from the top surface through to the depth of 75% of the overlay.

                  Microstructure

                  The typical overlay microstructure of Duroxite® 101 is composed of a high proportion of extremely hard primary M7C3 chromium-rich carbides with a typical hardness of 1700 HK4) dispersed evenly in a ductile eutectic austenite matrix. The volume fraction of primary carbides is maintained between 30 to 50 % to provide a good combination of wear resistance and homogenous bonding.

                  4) HK is the Knoop microhardness which is primarily used for very brittle materials.

                  Tolerances

                  Thickness

                  Overall and overlay thickness tolerances can be guaranteed within ±10% of specified thickness.

                  Flatness

                  Plate flatness tolerance can be guaranteed within ±3 mm (±1/8”) over 1.5 m (5’) plate length for plate dimensions equal to or less than 1.5 m (5’) x 3.0 m (10’). For plates greater than 1.5 m (5’) wide by 3.0 m (10’) long, the following flatness guarantees apply.

                  Hide/Show specific columns Edit
                  Select columns to display
                    Standard overlay thicknesses
                    Plate flatness tolerance gauranteed over 1.5m (5'),
                    Metric unit
                    Metric unit 1.5 m x 3.0 m 1.8 m x 3.0 m 2.4 m x 3.0 m
                    5 mm on 8 mm 12 mm 32 mm 38 mm
                    6 mm on 6 mm 12 mm 32 mm 38 mm
                    10 mm on 10 mm 6 mm 19 mm 25 mm
                    12 mm on 12 mm 3 mm 12 mm 12 mm
                    Compare parameters

                    Select one parameter to compare

                    Comparison

                      For custom sizes, please consult your local sales representative or Hardox Wearparts center for flatness guarantees.

                      Delivery Conditions

                      Duroxite® 101 is normally supplied in an as-welded condition, but can also be supplied in a ground condition upon request.

                      Fabrication and Other Recommendations

                      Welding, cutting, forming and machining

                      Recommendations can be found in the Duroxite® Products brochure, or consult your local technical support representative.

                      Safety precautions

                      When welding or cutting Duroxite® products, gases and harmful fumes are produced that are chemically complex and difficult to classify. The major toxic component in the fumes is hexavalent chromium. The proper exhaust ventilation equipment and fume-extraction torches are recommended, as well as suitable protective clothing and respiratory protection for operators.