Strenx performance steel
Strenx performance steel

Strenx® 100 XF

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    Show specs in Metric Imperial

    General Product Description

    Strenx® 100 XF cold-forming steel is a thermomechanically rolled product with a minimum yield strength of 690 MPa.

    Strenx® 100 XF is a cold forming steel for light- and heavy transport solutions and components. Strenx® 100 XF meets the requirements of ASTM A1018 grade 100 and can be supplied according to A1018 specification on request. 

    Dimension Range

    Strenx® 100 XF is available in thicknesses of 2.0 - 10.0 mm, and in widths up to 1600 mm as coil, slit coil and as cut to length sheets in lengths up to 16000 mm.

    Mechanical Properties

    Hide/Show specific columns Edit
    Select columns to display
      Thickness
      (mminches)
      Yield strength ReH 1)
      (min MPaksi)
      Tensile strength Rm
      (min MPaksi)
      Elongation A50
      (min %)
      2.00 - 10.000.079 - 0.393 690100 760110 12
      Compare parameters

      Select one parameter to compare

      Comparison

        The mechanical properties are tested in the transverse direction.

        1) If ReH is not applicable then Rp0.2 is used.

        Impact Properties

        Hide/Show specific columns Edit
        Select columns to display
          Product Min. impact energy for longitudinal testing,
          Charpy V 10x10 mm test specimen
          Strenx® 100 XF 27 J / -40 °C
          Compare parameters

          Select one parameter to compare

          Comparison

            Product
            Strenx® 100 XF
            Min. impact energy for longitudinal testing,
            Charpy V 10x10 mm test specimen
            27 J / -40 °C

            Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 6 mm. The specified minimum value corresponds to a full-size specimen.

            Bending Properties

            Hide/Show specific columns Edit
            Select columns to display
              Bending t < 3.48 mm 3.48 ≤ t ≤ 6.00 mm t > 6.00 mm
              Min. inner bending radius for a 90° bend 0.8 xt 1.2 xt 1.6 xt
              Compare parameters

              Select one parameter to compare

              Comparison

                Valid in both the longitudinal and transverse direction.

                Chemical Composition (ladle analysis)

                Hide/Show specific columns Edit
                Select columns to display
                  C
                  (max %)
                  Si
                  (max %)
                  Mn
                  (max %)
                  P
                  (max %)
                  S
                  (max %)
                  Al
                  (min %)
                  Nb
                  (max %)
                  V
                  (max %)
                  Ti
                  (max %)
                  0.12 0.03 2.10 0.025 0.010 0.015 0.09 1) 0.20 1) 0.15 1)
                  Compare parameters

                  Select one parameter to compare

                  Comparison

                    Strenx® 100 XF is available with different levels of Si: from max 0.03%, up to max 0.28%. Max Si 0.03% is the standard version that is suitable for hot dip galvanizing with thin Zinc layers, and for products that will not be galvanized. If the material is to be hot-dip galvanized and a thicker Zinc layer is requested, this must be specified at the time of order.

                    1) Sum of Nb, V and Ti = max 0.22%.

                    Tolerances

                    More details are given in SSAB’s brochure Strenx® Guarantees.

                    Thickness

                    Tolerances according to Strenx® Thickness Guarantees.

                    Strenx® Guarantees offer considerably narrower thickness tolerances compared to EN 10051. 

                    Length and Width

                    Width and length tolerances according to SSAB standard.

                    The SSAB standard offer narrower width and length tolerances compared to EN 10051.

                    Length tolerances only apply for cut to length sheets.

                    Shape

                    Tolerances according to EN 10051.

                    Narrower tolerances according to the SSAB standard are available on request 

                    Flatness

                    Tolerances according to Strenx® Flatness Guarantees Class A.

                    Strenx® Flatness Guarantees offer narrower tolerances compared to EN 10051.

                    Flatness guarantees only apply for cut to length sheets. 

                    Surface Properties

                    According to EN 10163-2 Class A, Subclass 3.

                    Delivery Conditions

                    Thermomechanically Rolled. Strenx® 100 XF is available in as rolled or pickled surface condition with mill or cut edge.

                    Fabrication and Other Recommendations

                    Welding, bending and machining

                    Strenx® 100 XF has good welding, cold forming and cutting performance. Strenx® 100 XF is a cold forming steel not suited for heat treatments at temperatures above 1080°F (580°C) since the material then may lose its guaranteed properties.

                    For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

                    Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the product.