Docol® Tube 600LA

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

On this page

General Product Description

Docol® Tube 600LA is high-strength formable precision tube with pickled hot rolled surface condition. Available in circular, rectangular and square shapes. Customized shapes and other tailoring options are available upon request. Typical uses include automotive and engineering, where durability, formability, lightness and energy absorption are important.

Dimension Range

Docol Tube 600LA is available in circular, square and rectangular shapes.

Hide/Show specific columns Edit
Select columns to display
    Shapes Dimensions
    Circular (mmin) 22 - 88.90.87 - 3.50
    Square (mmin) 30x30 - 60x60
    Rectangular (mmin) 30x20 - 100x40
    Wall thickness (mmin) 2.0 - 3.00.079 - 0.12
    Mill length (mm) 6000
    Compare parameters

    Select one parameter to compare

    Comparison

      Shapes
      Circular (mmin)
      Dimensions
      22 - 88.90.87 - 3.50
      Shapes
      Square (mmin)
      Dimensions
      30x30 - 60x60
      Shapes
      Rectangular (mmin)
      Dimensions
      30x20 - 100x40
      Shapes
      Wall thickness (mmin)
      Dimensions
      2.0 - 3.00.079 - 0.12
      Shapes
      Mill length (mm)
      Dimensions
      6000

      Other shapes, sizes and lengths are available upon request.

      Circular Dimensions

      Hide/Show specific columns Edit
      Select columns to display
        Outer diameter (mmin) 2.0 mm (kg/m) 2.5 mm (kg/m) 3.0 mm (kg/m)
        220.87 0.986
        250.98 1.13
        281.1 1.28
        301.2 1.38
        321.3 1.48 1.82
        351.4 1.63 2.00
        381.5 1.78 2.19
        411.6 1.92 2.37
        44.51.75 2.10 2.59
        481.9 2.27 2.81
        502.0 2.37 2.93 3.48
        552.2 2.61 3.24 3.85
        572.2 2.71 3.36 4.00
        602.4 2.86 3.55 4.22
        76.13.00 3.65 4.54
        88.93.50 4.29 5.33
        Compare parameters

        Select one parameter to compare

        Comparison

          Square Dimensions

          Hide/Show specific columns Edit
          Select columns to display
            Height x Width (mm) 2.0 mm (kg/m) 2.5 mm (kg/m)
            30 x 30 1.75
            32 x 32 1.88 2.31
            35 x 35 2.07 2.54
            40 x 40 2.38 2.93
            50 x 50 3.01 3.72
            60 x 60 3.64 4.50
            Compare parameters

            Select one parameter to compare

            Comparison

              Rectangular Dimensions

              Hide/Show specific columns Edit
              Select columns to display
                Height x Width (mm) 2.0 mm (kg/m) 2.5 mm (kg/m)
                30 x 20 1.44
                30 x 25 1.59
                35 x 15 1.44
                35 x 20 1.59
                40 x 20 1.75
                40 x 25 1.91
                40 x 30 2.07
                50 x 20 2.07 2.54
                50 x 25 2.22 2.74
                50 x 30 2.38 2.93
                50 x 40 2.69 3.33
                60 x 20 2.38 2.93
                60 x 30 2.69 3.33
                60 x 40 3.01 3.72
                70 x 25 2.85 3.52
                70 x 30 3.01 3.72
                70 x 50 3.64 4.50
                80 x 20 3.01 3.72
                80 x 40 3.64 4.50
                80 x 60 4.26 5.29
                100 x 40 4.26 5.29
                Compare parameters

                Select one parameter to compare

                Comparison

                  Mechanical Properties

                  Hide/Show specific columns Edit
                  Select columns to display
                    Yield strength Rp0.2
                    (min MPa)
                    Tensile strength Rm
                    (min MPa)
                    Elongation A
                    (min %)
                    HR600LA 600 640 6
                    Compare parameters

                    Select one parameter to compare

                    Comparison

                      Mechanical properties meet the requirements of EN 10305 (+CR2).

                      Chemical Composition (ladle analysis)

                      Hide/Show specific columns Edit
                      Select columns to display
                        C
                        (max %)
                        Si
                        (max %)
                        Mn
                        (max %)
                        P
                        (max %)
                        S
                        (max %)
                        Altot 1)
                        (min %)
                        HR600LA 0.16 0.60 1.80 0.025 0.025 0.020
                        Compare parameters

                        Select one parameter to compare

                        Comparison

                          Chemical composition meets the requirements of EN 10305.

                          If other chemical elements such as Ti, Nb or V are used, the content of these elements are reported in the inspection document.

                          1) This requirement is not applicable provided the steel contains a sufficient amount of other nitrogen binding elements, such as Ti, Nb or V.

                          Tolerances

                          Tolerance Circular

                          Hide/Show specific columns Edit
                          Select columns to display
                            Characteristic Circular precision tubes
                            Tolerances based on the requirements of EN 10305-3
                            Outside diameter (D) (1
                            D < 20 mm
                            20 ≤ D < 32 mm
                            32 ≤ D < 44 mm
                            44 ≤ D < 55 mm
                            55 ≤ D < 70 mm
                            70 ≤ D < 80 mm
                            80 ≤ D < 100 mm

                            ±0.12 mm
                            ±0.15 mm
                            ±0.20 mm
                            ±0.25 mm
                            ±0.30 mm
                            ±0.35 mm
                            ±0.40 mm
                            Out-of-roundness The diameter tolerances include the out-of-roundness
                            Thickness (T) T ≤ 1.5 mm: ±0.15 mm
                            T>1.5 mm: ±10% of nominal thickness or ±0.35 mm whichever is the smaller
                            Straightness Maximum 0.15% of measured length
                            Height of internal weld bead, g;
                            Bead removed
                            Bead not removed

                            g ≤ 0.3 mm
                            g < 0.8 mm, when T ≤ 1.5 mm
                            g < 0.6 x T, when 1.5 mm < T ≤ 3.0 mm
                            Mill length 0/+50 mm, standard length 6000 mm
                            Exact length, single cutting Agreed at the time of enquiry and order
                            Exact length, bundle cutting Agreed at the time of enquiry and order
                            Compare parameters

                            Select one parameter to compare

                            Comparison

                              Characteristic
                              Outside diameter (D) (1
                              D < 20 mm
                              20 ≤ D < 32 mm
                              32 ≤ D < 44 mm
                              44 ≤ D < 55 mm
                              55 ≤ D < 70 mm
                              70 ≤ D < 80 mm
                              80 ≤ D < 100 mm
                              Circular precision tubes
                              Tolerances based on the requirements of EN 10305-3

                              ±0.12 mm
                              ±0.15 mm
                              ±0.20 mm
                              ±0.25 mm
                              ±0.30 mm
                              ±0.35 mm
                              ±0.40 mm
                              Characteristic
                              Out-of-roundness