Docol® 1000CP complex phase

More about complex phase steel

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

On this page

General Product Description

Docol® 1000CP is made for cold forming and allows for a tight bending radius on high-strength applications. These steels are characterized by both a high yield strength and an improved cleanliness, which allows for a tight radius.

Dimension Range

Cold rolled / UC, EG: thickness 0.50-2.10 mm, width up to 1527 mm.

Cold rolled / GI: thickness 0.95-2.00 mm, width up to 1250 mm.

Hot rolled / UC: thickness 2.50-4.00 mm, width up to 1510 mm.

Slit strip and cut to length sheets are available upon request.

Grade and coating specific restrictions on available dimensions may occur.

Mechanical Properties

Hide/Show specific columns Edit
Select columns to display
    Standard Coating Test direction
    Yield strength Rp0.2
    (MPa)
    Tensile strength Rm
    (MPa)
    Elongation A80
    (min %)
    Elongation A50
    (min %)
    BH2
    (min MPa)
    Docol CR​780Y​980T-​CP VDA 239-100 UC, EG, GI L 780 - 950 980 - 1140 6 1) 30
    Docol Roll 1000 SSAB UC, EG T 800 - 950 980 - 1140 6 30
    Docol Roll 1000HY SSAB UC, EG T 850 - 1000 - 1200 5 30
    Docol HR​720Y​950T-​CP SSAB UC* L 720 - 900 950 - 1130 10 30
    Docol HR​800Y​950T-​CP SSAB UC* T 800 - 920 950 - 1050 9 30
    Compare parameters

    Select one parameter to compare

    Comparison

      *Available upon request.

      The testing of mechanical properties of electrogalvanized products is conducted without coating.

      1) Decreased minimum elongation values apply for product thickness t < 0.60 mm (minus 2 units).

      Chemical Composition (ladle analysis)

      Hide/Show specific columns Edit
      Select columns to display
        Coating C
        (max %)
        Si
        (max %)
        Mn
        (max %)
        P
        (max %)
        S
        (max %)
        Al
        (%)
        Nb+Ti
        (max %)
        Cr+Mo
        (max %)
        B
        (max %)
        Cu
        (max %)
        Docol CR​780Y​980T-​CP UC, EG, GI 0.23 1.00 2.70 0.050 0.010 0.015 - 1.00 0.15 1.00 0.005 0.20
        Docol Roll 1000 UC, EG 0.16 0.40 1.80 0.020 0.010 From 0.015 0.10
        Docol Roll 1000HY UC, EG 0.16 0.40 1.80 0.020 0.010 From 0.015 0.10
        Docol HR​720Y​950T-​CP UC* 0.18 1.00 2.20 0.050 0.010 0.015 - 1.2 0.25 1.00 0.005 0.25
        Docol HR​800Y​950T-​CP UC* 0.18 1.00 2.20 0.050 0.010 From 0.015 0.25 1.00 0.005 0.25
        Compare parameters

        Select one parameter to compare

        Comparison

          * Available upon request.

          Tolerances

          Cold rolled (UC, EG): Tolerances in accordance to EN 10131.

          Hot rolled (UC): Tolerances in accordance to EN 10051.

          Hot-dip galvanized (GI): Tolerances in accordance to EN 10143.

          Customized dimensional and shape tolerances are available upon request.

          Coatings

          The metal coating options for Docol products include:

          Hot-dip zinc coating (GI) consists almost entirely of zinc (>99%). It is lead free, resulting in a small zinc spangle size. The coating provides good corrosion protection.

          Electrogalvanized coating (EG) is applied continuously by electro deposition. The coating consists of zinc (>99%). Electrogalvanized steel is characterized by its excellent surface quality and uniform coating thickness.

          Grade specific availability of metal coatings for Docol products is given in the Mechanical properties table (Coating).

          Hide/Show specific columns Edit
          Select columns to display
            Coating type Coating class Standard Closest in EN standard, informative 1) Coating mass per side, single spot test (g/m2) Thickness per side informative (µm)
            GI 40/40 VDA 239-100 Z100 40 - 60 5.6 - 8.5
            GI 50/50 VDA 239-100 50 - 70 7.0 - 9.9
            GI 60/60 VDA 239-100 Z140 60 - 90 8.5 - 12.7
            GI 70/70 VDA 239-100 70 - 100 9.9 - 14.1
            GI 85/85 VDA 239-100 85 - 115 12.0 - 16.2
            GI 115/115 VDA 239-100 Z275 115 - 155 16.2 - 21.8
            EG 12/12 VDA 239-100 ZE25/25 12 - 32 1.7 - 4.5
            EG 18/18 VDA 239-100 18 - 38 2.5 - 5.4
            EG 29/29 VDA 239-100 ZE50/50 29 - 49 4.1 - 6.9
            EG 47/47 VDA 239-100 ZE75/75 47 - 61 6.6 - 8.6
            EG 50/50 VDA 239-100 50 - 70 7.0 - 9.9
            EG 53/53 VDA 239-100 53 - 73 7.5 - 10.3
            EG 60/60 VDA 239-100 60 - 80 8.5 - 11.3
            EG 65/65 VDA 239-100 ZE100/100 65 - 85 9.2 - 12.0
            EG 70/70 VDA 239-100 70 - 90 9.9 - 12.7
            Compare parameters

            Select one parameter to compare

            Comparison

              Docol metal coated products are available with surface quality for unexposed applications.

              In addition to these coating masses, OEM specific coatings and single sided EG coatings are available upon request.

              1) For GI and GA the closest informative value refers to EN 10346. For EG to EN 10152.

              Surface Treatments

              Uncoated (UC): available as oiled.

              Hot-dip galvanized (GI): available as oiled and/or chemically passivated.

              Electrogalvanized (EG): available as oiled and/or chemically passivated or phosphated.

              All surface treatments are in accordance with RoHS directive (2011/65/EU) and do not contain Chromium VI (Cr6+). Surface treatments provide only temporary surface protection during transportation and storage. In order to avoid corrosion damages, care must be taken to keep the products dry during transportation and storage. If they become wet, they must be separated and situated so that they are dried quickly.

              Fabrication and Other Recommendations

              For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

              Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.

              Docol® Complex Phase steel product offer

              Docol® 600 CP complex phase

              Docol® 800CP complex phase

              Docol® 1000CP complex phase

              Docol® 1200CP complex phase

              Related content