COR-TEN® A, hot rolled

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    General Product Description

    With its anti-corrosive properties, COR-TEN® minimizes the need for maintenance and corrosion-prevention treatment, contributing significantly to low maintenance costs throughout the product lifecycle. In addition to low maintenance costs, the reduced need for corrosion prevention means less use of paint and solvents, making COR-TEN® an environmental friendly choice of steel.

    Typical applications are structural components for buildings, transmission poles, bridges and many others.

    Dimension Range

    COR-TEN® A Hot rolled is available in thickness 2.00-12.70 mm and width up to 1860 mm as coil, slit coil and cut to length and 3300 mm as plate. Length up to 16 meters as cut to length and 13 meters as plate.

    Mechanical Properties

    Hide/Show specific columns Edit
    Select columns to display
      Yield strength ReL
      (min MPa)
      Tensile strength Rm
      (min MPa)
      Elongation A50
      (min %)
      Min. bending radius 90° bend
      345 485 20 2.0 x t
      Compare parameters

      Select one parameter to compare

      Comparison

        The mechanical properties are tested transverse to the direction of rolling.

        Chemical Composition (ladle analysis)

        Hide/Show specific columns Edit
        Select columns to display
          C
          (max %)
          Si
          (%)
          Mn
          (%)
          P
          (%)
          S
          (max %)
          Al
          (%)
          Cu
          (%)
          Cr
          (%)
          Ni
          (max %)
          0.12 0.25 - 0.75 0.20 - 0.50 0.07 - 0.15 0.030 0.015 - 0.06 0.25 - 0.55 0.50 - 1.25 0.65
          Compare parameters

          Select one parameter to compare

          Comparison

            Carbon Equivalent CEV

            Hide/Show specific columns Edit
            Select columns to display
              Delivery form Hot rolled strip Hot rolled plate
              Thickness (mmin) 2 - 12.70.08 - 0.500 6 - 12.70.2 - 0.500
              Typical CEV (%) 0.35 0.39
              Compare parameters

              Select one parameter to compare

              Comparison

                Tolerances

                COR-TEN® A is delivered with SSAB Weathering tolerances, with improved guarantees compared to corresponding EN standards. More details are available at SSAB.com

                Thickness

                Hot rolled Strip: Thickness tolerances correspond to ⅔ of EN 10051 as default value. After special agreement, tolerances down to ½ of EN 10051 can be delivered for certain products and dimensions.

                Plate: Thickness tolerances that correspond to ¾ of EN 10029 as default value.

                Length and Width

                Hot rolled Strip: Width and length tolerances according to SSAB standard which offer narrower tolerances compared to EN 10051.

                For coil and sheet with mill edge, the width tolerances are corresponding to -0/+20 mm.

                For coil and sheet with cut edge, the width tolerances are corresponding to -0/+2 mm.

                Length tolerances only apply for cut to length sheets.

                Plate: Width tolerance is -0/+4-10mm depending on the thickness. Length tolerances are -0/+15-75mm depending on length.

                Shape

                Hot rolled Strip: Shape tolerances in accordance to EN 10051. Narrower tolerances according to the SSAB standard are available on request.

                Plate: Shape tolerances in accordance to EN 10029.

                Flatness

                Strip: 

                Flatness tolerances guarantee a maximum flatness deviation of 3 mm/m in addition to the EN 10051 flatness requirements.

                Flatness guarantees only apply for cut to length sheets.

                Plate: Max flatness deviation 6 mm/m.

                Surface Properties

                According to EN 10163-2 Class A, Subclass 3.

                Delivery Conditions

                Coils, slit coils and cut to length: Controlled rolled or thermomechanically rolled.

                Plate: Hot-rolled, normalized rolled or normalized in furnace.


                Inspection documents

                The inspection document shall be specified at the time of order. The European types of inspection documents are defined in the EN 10204 standard.

                Fabrication and Other Recommendations

                COR-TEN®  A has extra corrosion resistance with good formability, thoughness and weldability.

                COR-TEN®  is an internationally registered trademark of United States Steel Corporation.

                For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

                Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.

                Contact Information

                www.ssab.com/contact