SSAB Laser® 275C

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    General Product Description

    SSAB Laser® 275C is an advanced structural cold forming steel for laser cutting. The SSAB guarantee for flatness, both before and after laser cutting, is ≤ 3 mm/m deviation.

    SSAB Laser® 275C meets and exceeds the requirements of S275J2C+N in EN 10025-2. Dual certification and CE marking are available upon request.

    Dimension Range

    Hide/Show specific columns Edit
    Select columns to display
      Delivery form Thickness
      (mmin)
      Width
      (mmin)
      Length
      (mmin)
      Hot rolled sheet as rolled 2.0 - 16.00.079 - 0.630 1000 - 186039.37 - 73.23 1000 - 1600039.37 - 629.92
      Hot rolled sheet pickled and oiled 2.0 - 16.00.079 - 0.630 1000 - 183039.37 - 72.05 1000 - 1600039.37 - 629.92
      Hot rolled plate as rolled 8.0 - 30.00.31 - 1.18 1000 - 330039.37 - 129.9 2000 - 1500078.74 - 590.55
      Compare parameters

      Select one parameter to compare

      Comparison

        Mechanical Properties

        Hide/Show specific columns Edit
        Select columns to display
          Delivery form Thickness
          (mmin)
          Yield strength Re
          (min MPa)
          Tensile strength Rm
          (MPa)
          Elongation A80 2)
          (min %)
          Elongation A5 3)
          (min %)
          Min. inner bending radius 90° t ≤ 6mm 4)
          (x t)
          Min. inner bending radius 90° t ˃ 6mm 4)
          (x t)
          Hot rolled sheet 2.0 - 16.00.079 - 0.630 275 410 - 560 1) 17 21 1.0 1.0
          Hot rolled plate 8.0 - 30.00.31 - 1.18 275 410 - 560 21 1.0
          Compare parameters

          Select one parameter to compare

          Comparison

            The mechanical properties are tested transverse to the direction of rolling.

            1) For thickness ˂ 3mm the tensile strength is 430-580 MPa.

            2) A80 value applies for thicknesses < 3.00 mm.

            3) A5 value applies for thicknesses ≥ 3.00 mm.

            4) The bending guarantee is valid for both longitudinal and transverse direction.

            Impact Properties

            Hide/Show specific columns Edit
            Select columns to display
              Min. impact energy for longitudinal testing,
              Charpy V 10x10 mm test specimens
              40 J / -20 °C
              Compare parameters

              Select one parameter to compare

              Comparison

                Min. impact energy for longitudinal testing,
                Charpy V 10x10 mm test specimens
                40 J / -20 °C
                Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 6mm. The specified minimum value corresponds to a full-size specimen.

                Chemical Composition (heat analysis)

                Hide/Show specific columns Edit
                Select columns to display
                  Delivery form C
                  (max %)
                  Si
                  (max %)
                  Mn
                  (max %)
                  P
                  (max %)
                  S
                  (max %)
                  CEV
                  (max )
                  Hot rolled sheet 0.18 0.03 1.60 0.020 0.020 0.39
                  Hot rolled plate 0.19 0.03 1.60 0.020 0.020 0.42
                  Compare parameters

                  Select one parameter to compare

                  Comparison

                    All SSAB Laser® steels are aluminum-killed (Al ≥ 0.015%) and grain-refined. Additionally, niobium (Nb), vanadium (V), titanium (Ti) and/or boron (B) may be used as single alloying element or in any combination.

                    Tolerances

                    All SSAB Laser® products are delivered with SSAB Laser® tolerances, which means increased guarantees compared to corresponding EN standards. Detailed information is available on ssab.com.

                    Thickness

                    Hot rolled sheet: SSAB Laser® tolerances correspond to ⅔ of EN 10051 as default. Tighter tolerances are available upon request.

                    Hot rolled plate: SSAB Laser® tolerances correspond to ¾ of EN 10029 as default.

                    Width

                    Hot rolled sheet: -0/+20 mm for mill edge sheet; -0/+2 mm for cut edge sheet. Tighter tolerances are available upon request.

                    Hot rolled plate: -0/+4-10mm depending on the thickness.

                    Length

                    Hot rolled sheet:

                    Hide/Show specific columns Edit
                    Select columns to display
                      Nominal length
                      (mm)
                      Tolerance
                      (mmin)
                      l ≤ 4000 - 0 / + 3- 0 / + 0.1
                      4000 ˂ l ≤ 6000 - 0 / + 4- 0 / + 0.2
                      6000 ˂ l ≤ 8000 - 0 / + 5- 0 / + 0.2
                      8000 ˂ l ≤ 13000 - 0 / + 6- 0 / + 0.2
                      13000 ˂ l ≤ 16000 - 0 / + 8- 0 / + 0.3
                      Compare parameters

                      Select one parameter to compare

                      Comparison

                        Nominal length
                        (mm)
                        l ≤ 4000
                        Tolerance
                        (mmin)
                        - 0 / + 3- 0 / + 0.1
                        Nominal length
                        (mm)
                        4000 ˂ l ≤ 6000
                        Tolerance
                        (mmin)
                        - 0 / + 4- 0 / + 0.2
                        Nominal length
                        (mm)
                        6000 ˂ l ≤ 8000
                        Tolerance
                        (mmin)
                        - 0 / + 5- 0 / + 0.2
                        Nominal length
                        (mm)
                        8000 ˂ l ≤ 13000
                        Tolerance
                        (mmin)
                        - 0 / + 6- 0 / + 0.2
                        Nominal length
                        (mm)
                        13000 ˂ l ≤ 16000
                        Tolerance
                        (mmin)
                        - 0 / + 8- 0 / + 0.3

                        Hot rolled plate:

                        Hide/Show specific columns Edit
                        Select columns to display
                          Nominal length
                          (mm)
                          Tolerance
                          (mm)
                          2000 ˂ l ≤ 10000 - 0 / + 15
                          10000 ˂ l ≤ 15000 - 0 / + 20
                          Compare parameters

                          Select one parameter to compare

                          Comparison

                            Nominal length
                            (mm)
                            2000 ˂ l ≤ 10000
                            Tolerance
                            (mm)
                            - 0 / + 15
                            Nominal length
                            (mm)
                            10000 ˂ l ≤ 15000
                            Tolerance
                            (mm)
                            - 0 / + 20

                            Shape

                            Hot rolled sheet: according to EN 10051.

                            Hot rolled plate: according to EN 10029.

                            Flatness

                            Hot rolled sheet: ≤ 3 mm/m flatness deviation for both delivery condition and laser cut parts.

                            Hot rolled plate: ≤ 3 mm/m flatness deviation for both delivery condition and laser cut parts.

                            Surface Properties

                            According to EN 10163-2 Class A, Subclass 3.

                            Delivery Conditions

                            Normalized rolled.

                            Surface and edge condition

                            Hot rolled sheet: as rolled or pickled and oiled surface condition with mill edge. Cut edge is available upon request.

                            Hot rolled plate: as rolled surface condition and cut edges as default.

                            Fabrication and Other Recommendations

                            All SSAB Laser® products have been optimized for laser cutting, cold forming and welding.

                            For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

                            Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.

                            Contact Information

                            www.ssab.com/contact