Strenx® Section 900MC

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    General Product Description

    Strenx® Section 900MC is a cold-formed steel section made of hot-rolled, high-strength steel with a minimum yield strength of 900 MPa.

    Its high-strength combined with naturally stiff form enables construction of stronger and lighter structures. Typical applications include demanding load-bearing structures in the lifting, handling and transportation segments.

    The steel in Strenx® Section 900MC meets or exceeds the requirements of EN 10149-2. Its tolerances meet or exceed, when applicable, the requirements of EN 10162.

    Strenx® Section 900MC is available as U-section. Other shapes and variations are available upon request. The maximum length of the sections is 21 meters, cut-to-length sections are available upon request.

    Dimension Range

    Strenx® Section 900MC is available as U-section. Other shapes and variations are available upon request.

    Hide/Show specific columns Edit
    Select columns to display
      Product type U-Section
      Bottom length (mmin) 200 - 4007.874 - 15.748
      Side length (mmin) 50 - 1501.969 - 5.906
      Wall thickness (mmin) 3.0 - 6.00.118 - 0.236
      Max. length (mmin) 12000826.770
      Compare parameters

      Select one parameter to compare

      Comparison

        Product type
        Bottom length (mmin)
        U-Section
        200 - 4007.874 - 15.748
        Product type
        Side length (mmin)
        U-Section
        50 - 1501.969 - 5.906
        Product type
        Wall thickness (mmin)
        U-Section
        3.0 - 6.00.118 - 0.236
        Product type
        Max. length (mmin)
        U-Section
        12000826.770

        Mechanical Properties

        Hide/Show specific columns Edit
        Select columns to display
          Thickness
          (mmin)
          Yield strength ReH 1)
          (min MPaksi)
          Tensile strength Rm
          (MPaksi)
          Elongation A80
          (min %)
          Min. inner bending radius for a 90° bend
          (x t)
          3.00 - 6.000.118 - 0.236 900130 930 - 1200135 - 174 8 3.0
          Compare parameters

          Select one parameter to compare

          Comparison

            The mechanical properties are tested in the longitudinal direction.

            1) If ReH is not applicable then Rp0.2 is used. On thicknesses >8 mm the minimum yield strength may be 20MPa lower.

            Impact Properties

            Hide/Show specific columns Edit
            Select columns to display
              Product Min. impact energy for longitudinal testing,
              Charpy V 10x10 mm test specimen 1)
              Strenx® Section 900MC 27 J / -40 °C20 ft-lbs / -40 °F
              Compare parameters

              Select one parameter to compare

              Comparison

                Product
                Strenx® Section 900MC
                Min. impact energy for longitudinal testing,
                Charpy V 10x10 mm test specimen 1)
                27 J / -40 °C20 ft-lbs / -40 °F

                1) Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 6 mm. The specified minimum value corresponds to a full-size specimen.

                Chemical Composition (ladle analysis)

                Hide/Show specific columns Edit
                Select columns to display
                  C
                  (max %)
                  Si
                  (max %)
                  Mn
                  (max %)
                  P
                  (max %)
                  S
                  (max %)
                  Altot
                  (min %)
                  Nb
                  (max %)
                  V
                  (max %)
                  Ti
                  (max %)
                  0.12 0.25 1.30 0.020 0.010 0.015 0.050 0.05 0.07
                  Compare parameters

                  Select one parameter to compare

                  Comparison

                    If the material is to be hot-dip galvanized according to category A or category B in EN 10149-2 this must be specified at the time of order. 

                    Sum of Nb, V and Ti = max 0.22%

                    The steel is grain refined.

                    Carbon Equivalent CET(CEV)

                    Hide/Show specific columns Edit
                    Select columns to display
                      Thickness (mmin) 3.0 - 6.00.118 - 0.236
                      Typ CET(CEV) 0.28 (0.51)
                      Compare parameters

                      Select one parameter to compare

                      Comparison

                        Thickness (mmin)
                        Typ CET(CEV)
                        3.0 - 6.00.118 - 0.236
                        0.28 (0.51)
                        CET and CEV formula

                        Tolerances

                        Tolerances according to EN 10162 when applicable.

                        Narrower tolerances are available upon request.

                        Delivery Conditions

                        The sections are roll formed from thermomechanically rolled steel.

                        Fabrication and Other Recommendations

                        Welding, bending and machining

                        Strenx® Section has good weldabilility, including corner region, and it is suitable for thermal cutting. All the common welding methods are suitable with matching or undermatching consumables.

                        Sections can also be sawed and machined with regular tools. Bending of the sections is also possible, please contact Tech Support for further instructions. For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

                        Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the product.