Strenx® 700 CR

Download data sheet

Select Language

Get datasheet by email

Get datasheet by email

    Strenx® 700 CR high-strength structural steel

    Strenx® 700 CR is a cold-rolled high-strength structural steel with a minimum yield strength of 700 MPa. This steel is used to produce a wide range of strong and light equipment. Strenx® 700 CR is covered by the Strenx® guarantees for flatness, thickness and bending properties, ensuring predictable performance in the workshop. The steel is available as thin sheets or coils with thicknesses between 0.7 and 2.1 mm, width up to 1500 mm and cut-to-length sheets up to 8500 mm.

    Show specs in Imperial Metric

    Dimension Range

    Strenx® 700 CR is available in thicknesses of 0.028" - 0.083", widths up to 59.055" and in lengths up to 334.645", when delivered as cut-to-length sheets.

    Mechanical Properties

    Hide/Show specific columns Edit
    Select columns to display
      Yield strength Rp0.2
      (min ksiMPa)
      Tensile strength Rm
      Elongation A80
      (min %)
      Min. inner bending radius for a 90° bend 1)
      (x t)
      101700 145 - 1741000 - 1200 7 2.0
      Compare parameters

      Select one parameter to compare


        1) For both longitudinal and transverse direction.
        The mechanical properties are tested in the longitudinal direction.

        Chemical Composition (heat analysis)

        Hide/Show specific columns Edit
        Select columns to display
          (max %)
          (max %)
          (max %)
          (max %)
          (max %)
          (min %)
          (max %)
          0.16 0.40 1.80 0.020 0.010 0.015 0.10
          Compare parameters

          Select one parameter to compare


            Carbon Equivalent CET(CEV)

            Hide/Show specific columns Edit
            Select columns to display
              Thickness (inmm) 0.028 - 0.0830.7 - 2.1
              Typ CET(CEV) 0.29 (0.40)
              Compare parameters

              Select one parameter to compare


                Thickness (inmm)
                Typ CET(CEV)
                0.028 - 0.0830.7 - 2.1
                0.29 (0.40)
                CET and CEV formula


                More details are given in SSAB’s brochure Strenx® Guarantees.


                Tolerances according to Strenx® Thickness Guarantees.

                Strenx® Thickness guarantees meet the normal thickness tolerance requirements of EN 10131.

                Length and Width

                Tolerances according to EN 10131. Narrower tolerances according to the SSAB standard are available on request.

                Length tolerances only apply for cut to length sheets. 


                Tolerances according to Strenx® Flatness Guarantees Class B.

                Strenx® Flatness Guarantees offer narrower tolerances compared to EN 10131.

                Flatness guarantees only apply for cut to length sheets.

                Delivery Conditions

                Cold rolled. Strenx® CR is available with mill or cut edge.

                Delivery requirements can be found in SSAB’s brochure Strenx® Guarantees or

                Fabrication and Other Recommendations

                Welding, bending and machining

                Strenx® CR has good cold forming, welding and cutting performance.

                For information concerning fabrication, see SSAB´s brochures on or consult Tech Support.

                Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.

                Build it with 37% higher strength

                By upgrading from Strenx® 700 CR to Strenx® 960 CR, you gain 37% higher yield strength. This gives you opportunities to redesign your equipment for increased performance and reduced weight. Get in touch with our steel specialists at SSAB Tech Support or SSAB Knowledge Service Center for an update on upgrading.