General Product Description
The high-strength structural steel at 87 ksi.
Strenx® 600MC D/E is a hot-rolled structural steel made for cold forming, with a minimum yield strength of 87 ksi for stronger and lighter structures. Strenx® 600MC D/E meets or exceeds the requirements of S600MC in EN 10149-2.
Typical applications include a wide range of components and parts, such as demanding load-bearing structures. Strenx® 600MC D/E comes in coils, slit coils or cut-to-length sheets.
Mechanical Properties
(inmm)
(inmm)
(min ksiMPa)
(ksiMPa)
(min %)
(min %)
(inmm)
(inmm)
(min ksiMPa)
(ksiMPa)
(min %)
(min %)
(inmm)
(inmm)
(min ksiMPa)
(ksiMPa)
(min %)
(min %)
The mechanical properties are tested in the longitudinal direction.
1) If ReH is not applicable then Rp0.2 is used.
2) A80 value applies for thicknesses < 3.00 mm.
3) A5 value applies for thicknesses ≥ 3.00 mm.
4) For both longitudinal and transverse direction.
Impact Properties
1) Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 0.236". The specified minimum value corresponds to a full-size specimen.
Chemical Composition (heat analysis)
(max %)
(max %)
(max %)
(max %)
(max %)
(max %)
(max %)
(max %)
(max %)
1) If the material is to be hot-dip galvanized according to category A or category B in EN 10149-2 this must be specified at the time of order.Other galvanizing classes with higher Si-content are available after agreement.
2) Sum of Nb, V and Ti = max 0.22%.
The steel is grain refined.
Carbon Equivalent CET(CEV)
Thickness
Tolerances according to Strenx® Thickness Guarantee.
Strenx® Guarantees offer considerably narrower thickness tolerances compared to EN 10051.
Length and Width
Width and length tolerances according to SSAB standard.
SSAB standard offer narrower width and length tolerances compared to EN 10051.
Length tolerances only apply for cut to length sheets.
Shape
Tolerances according to EN 10051. Narrower tolerances according to the SSAB standard are available on request.
Flatness
Tolerances according to Strenx® Flatness Guarantee Class A.
Strenx® Flatness Guarantee offer narrower tolerances compared to EN 10051.
Flatness guarantees only apply for cut to length sheets.
Surface Properties
According to EN 10163-2 Class A, Subclass 3.
Delivery Conditions
Thermomechanically Rolled. Strenx® 600MC D/E is available in as rolled or pickled surface condition with mill or cut edge.
Delivery requirements can be found in SSAB’s brochure Strenx® Guarantees or on www.ssab.com.
Fabrication and Other Recommendations
Welding, bending and machining
Strenx® 600MC D/E has good welding, cold forming and cutting performance.
Strenx® 600MC D/E is a cold forming steel not suited for heat treatments at temperatures above 1076°F since the material then may lose its guaranteed properties.
For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.
Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.
Show specs in:
Ready to upgrade?
You can improve the performance and reduce the weight of your equipment by upgrading from Strenx® 600MC to Strenx® 700MC. A 17% higher yield strength means a higher load-bearing capacity. Get in touch with our steel specialists at SSAB Tech Support or SSAB Knowledge Service Center for an update on upgrading.