Strenx® Section 650MC

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    Show specs in Imperial Metric

    General Product Description

    Strenx® Section 650MC is a cold-formed steel section made of hot-rolled, high-strength steel with a minimum yield strength of 650 MPa.

    Its high-strength combined with naturally stiff form enables construction of stronger and lighter structures. Typical applications include demanding load-bearing structures in the lifting, handling and transportation segments.

    Strenx® Section 650MC is available as U-section. Other shapes and variations are available upon request. The maximum length of the sections is 826.770", cut-to-length sections are available upon request. 

    Dimension Range

    Strenx® Section 650MC is available as U-section. Other shapes and variations are available upon request.

    Hide/Show specific columns Edit
    Select columns to display
      Product type U-Section
      Bottom length (inmm) 1.969 - 15.74850 - 400
      Side length (inmm) 1.181 - 7.87430 - 200
      Wall thickness (inmm) 0.098 - 0.3142.5 - 8.0
      Max. length (inmm) 826.77012000
      Compare parameters

      Select one parameter to compare

      Comparison

        Product type
        Bottom length (inmm)
        U-Section
        1.969 - 15.74850 - 400
        Product type
        Side length (inmm)
        U-Section
        1.181 - 7.87430 - 200
        Product type
        Wall thickness (inmm)
        U-Section
        0.098 - 0.3142.5 - 8.0
        Product type
        Max. length (inmm)
        U-Section
        826.77012000

        Mechanical Properties

        Hide/Show specific columns Edit
        Select columns to display
          Thickness
          (inmm)
          Yield strength ReH 1)
          (min ksiMPa)
          Tensile strength Rm
          (ksiMPa)
          Elongation A80
          (min %)
          Elongation A5
          (%)
          Min. inner bending radius for a 90° bend
          (x t)
          0.098 - 0.1182.50 - 3.00 94650 101 - 123700 - 850 12 0.8
          0.118 - 0.2363.01 - 6.00 94650 101 - 123700 - 850 14 1.2
          0.237 - 0.3146.01 - 8.00 94650 101 - 123700 - 850 14 1.5
          Compare parameters

          Select one parameter to compare

          Comparison

            The mechanical properties are tested in the longitudinal direction.

            1) If ReH is not applicable then Rp0.2 is used. On thicknesses >0.315" the minimum yield strength may be 2.9 ksi lower.

            Impact Properties

            Hide/Show specific columns Edit
            Select columns to display
              Product Min. impact energy for longitudinal testing,
              Charpy V 0.393x0.393" test specimen 1)
              Strenx® Section 650MC 20 ft-lbs / -40 °F27 J / -40 °C
              Compare parameters

              Select one parameter to compare

              Comparison

                Product
                Strenx® Section 650MC
                Min. impact energy for longitudinal testing,
                Charpy V 0.393x0.393" test specimen 1)
                20 ft-lbs / -40 °F27 J / -40 °C

                1) Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 0.236". The specified minimum value corresponds to a full-size specimen.

                Chemical Composition (heat analysis)

                Hide/Show specific columns Edit
                Select columns to display
                  C
                  (max %)
                  Si
                  (max %)
                  Mn
                  (max %)
                  P
                  (max %)
                  S
                  (max %)
                  Altot
                  (min %)
                  Nb
                  (max %)
                  V
                  (max %)
                  Ti
                  (max %)
                  0.12 0.21 2.00 0.025 0.010 0.015 0.090 0.20 0.15
                  Compare parameters

                  Select one parameter to compare

                  Comparison

                    If the material is to be hot-dip galvanized according to category A or category B in EN 10149-2 this must be specified at the time of order. 

                    Sum of Nb, V and Ti = max 0.22%

                    The steel is grain refined.

                    Carbon Equivalent CET(CEV)

                    Hide/Show specific columns Edit
                    Select columns to display
                      Thickness (inmm) 0.098 - 0.3142.5 - 8.0
                      Typ CET(CEV) 0.22 (0.34)
                      Compare parameters

                      Select one parameter to compare

                      Comparison

                        Thickness (inmm)
                        Typ CET(CEV)
                        0.098 - 0.3142.5 - 8.0
                        0.22 (0.34)
                        CET and CEV formula

                        Tolerances

                        Tolerances according to EN 10162 when applicable. For Strenx® Sections with material thickness over 0.314" SSAB guarantees same tolerances as given in EN 10162 for thickness range 0.236"-0.314". Narrower tolerances are available upon request.

                        Delivery Conditions

                        The sections are roll formed from thermomechanically rolled steel.

                        Fabrication and Other Recommendations

                        Welding, bending and machining

                        Strenx® Section has good weldabilility, including corner region, and it is suitable for thermal cutting. All the common welding methods are suitable with matching or undermatching consumables.

                        Sections can also be sawed and machined with regular tools. Bending of the sections is also possible, please contact Tech Support for further instructions. For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

                        Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the product.