Duroxite® 100 WIRE

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

On this page

General Product Description

Duroxite® 100 Wire is a flux-cored welding wire for hardfacing components subject to severe sliding wear and moderate to low impact applications using an open-arc welding process. The weld deposit contains abrasion-resistant materials composed of a high proportion of extremely hard primary M7C3 chromium-rich carbides. With a typical hardness of 1700 HK *) these carbides are dispersed evenly in a ductile eutectic austenite matrix. It naturally reveals stress-relief cracks after welding.

Duroxite® 100 Wire is suitable for single-layer or multiple-layer deposits up to a maximum of three layers. Preheating, interpass temperature, and post-weld heat treatment are as needed according to base metal recommendations. If welding with downhill or uphill position, reduced wire feed speed and voltage are preferred to apply.

*) HK is the Knoop microhardness used primarily for very brittle materials.

Key Benefits

  • Same wear resistance guaranteed from surface through 75% depth of overlay in multi-layer deposit
  • Optimal alloy formulation that forms a carbide composition which provides a good combination of wear resistance and homogenous bonding

Typical Applications

Duroxite® 100 Wire is mainly designed to use for hardfacing wear parts undergoing wear by earth, sand and abrasives up to 350ºC (660ºF). Typical examples include: Crusher hammers, gyratory crusher cones and mantles, dredging pumps, slurry pipes, dragline bucket liners, coal pulverizer rolls, coke hammers, sand dredging parts, mining and earthmoving components, and sorting screens.

Standard Dimensions

Hide/Show specific columns Edit
Select columns to display
    Standard diameter
    Metric
    1.2 mm
    1.6 mm
    2.8 mm
    Compare parameters

    Select one parameter to compare

    Comparison

      Standard diameter
      Metric
      1.2 mm
      Standard diameter
      Metric
      1.6 mm
      Standard diameter
      Metric
      2.8 mm

      Mechanical Properties

      Hide/Show specific columns Edit
      Select columns to display

        ASTM G65 – Procedure A weight loss 2)

        Typical all-weld metal surface hardness 1)
        Number of overlay passes Classifications Surface
        (g max)
        75 % depth of overlay 3)
        (g max)
        Hardness: 2-layer deposit on mild steel Hardness: 3-layer deposit on mild steel
        Multiple passes DIN 14700 T Fe15 g
        DIN 8555 MF 10 GF 60 G
        0.18 0.18 58 - 65 HRC 60 - 65 HRC
        Compare parameters

        Select one parameter to compare

        Comparison

          1) Surface hardness is measured on machined flat surface just below overlay surface.

          2) ASTM G65 is a standard test measuring sliding abrasion resistance using a dry sand/rubber wheel apparatus. ASTM G65-Procedure A is the most severe test method.

          3) ASTM G65 wear test is conducted at 75% depth of the overlay materials to ensure consistently good wear resistance from the top surface through to the depth of 75% of the overlay.

          Test results for mechanical properties

          Test results for mechanical properties, deposit overlay chemical composition, surface hardness, and ASTM G65-A weight loss were obtained from a weld produced and tested according to prescribed standards, and should not be assumed to be the expected results in a particular application or weldment. Actual results will vary depending on many factors, including, but not limited to, weld procedure, substrate chemistry and working temperature, weldment design and fabrication methods. Users are cautioned to confirm by qualification testing, or other appropriate means, the suitability of any welding consumable and procedure before use in the intended applications.

          Chemical Composition

          Hide/Show specific columns Edit
          Select columns to display
            Standard diameter
            Typical all-weld metal analysis (Weight %)
            Metric C
            (%)
            Mn
            (%)
            Si
            (%)
            Cr
            (%)
            Fe
            1.2 mm0.04688 mm 0.045" 4.7 0.2 0.6 27 Balance
            1.6 mm0.06250 mm 5.5 0.2 0.6 29 Balance
            2.8 mm0.1094 mm 5.5 0.2 0.6 29 Balance
            Compare parameters

            Select one parameter to compare

            Comparison

              Welding recommendations

              Hide/Show specific columns Edit
              Select columns to display
                Welding conditions
                Current type Shielding gas Welding positions
                DCEP (Direct current electrode positive) None (Self-shielded) Flat, half up, half down
                Compare parameters

                Select one parameter to compare

                Comparison

                  Welding parameters recommendations

                  Hide/Show specific columns Edit
                  Select columns to display
                    Diameter
                    Amperage (A)
                    Voltage (V)
                    Stick-out
                    Metric Range Optimum Range Optimum Range Optimum
                    1.2 mm0.04688 mm 0.045" 110 - 250 190 24 - 30 28 20 mm - 45 mm 25 mm
                    1.6 mm0.06250 mm 150 - 270 200 25 - 30 28 20 mm - 45 mm 25 mm
                    2.8 mm0.1094 mm 250 - 450 300 28 - 32 30 20 mm - 45 mm 25 mm
                    Compare parameters

                    Select one parameter to compare

                    Comparison

                      Recovery: 90%

                      Delivery Conditions

                      Hide/Show specific columns Edit
                      Select columns to display
                        Standard package
                        Diameter
                        Weight
                        Type Metric Metric
                        Spool 1.2 mm0.04688 mm 0.045" 15 kg
                        Spool 1.6 mm0.06250 mm 15 kg
                        Spool 2.8 mm0.1094 mm 25 kg
                        Compare parameters

                        Select one parameter to compare

                        Comparison

                          Fabrication and Other Recommendations

                          The welded overlay components can be processed by welding, cutting, forming and machining. Specific recommendations can be found in the Duroxite® Product brochure or by consulting your local technical support representative.

                          Safety precautions

                          When welding or cutting Duroxite® products, gases and harmful fumes are produced that are chemically complex and difficult to classify. The major toxic component in the fumes is hexavalent chromium. The proper exhaust ventilation equipment and fume-extraction torches are recommended, as well as suitable protective clothing and respiratory protection for operators.