Strenx® 100 XF

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

On this page
Show specs in Metric Imperial

General Product Description

Strenx® 100 XF cold-forming steel is a thermomechanically rolled product with a minimum yield strength of 690 MPa.

Strenx® 100 XF is a cold forming steel for light- and heavy transport solutions and components. Strenx® 100 XF meets the requirements of ASTM A1018 grade 100 and can be supplied according to A1018 specification on request. 

Dimension Range

Strenx® 100 XF is available in thicknesses of 2.0 - 10.0 mm, and in widths up to 1600 mm as coil, slit coil and as cut to length sheets in lengths up to 16000 mm.

Mechanical Properties

Hide/Show specific columns Edit
Select columns to display
    Thickness
    (mmin)
    Yield strength ReH 1)
    (min MPaksi)
    Tensile strength Rm
    (min MPaksi)
    Elongation A50
    (min %)
    2.00 - 10.000.079 - 0.393 690100 760110 12
    Compare parameters

    Select one parameter to compare

    Comparison

      The mechanical properties are tested in the transverse direction.

      1) If ReH is not applicable then Rp0.2 is used.

      Impact Properties

      Hide/Show specific columns Edit
      Select columns to display
        Product Min. impact energy for longitudinal testing,
        Charpy V 10x10 mm test specimen
        Strenx® 100 XF 27 J / -40 °C20 ft-lbs / -40 °F
        Compare parameters

        Select one parameter to compare

        Comparison

          Product
          Strenx® 100 XF
          Min. impact energy for longitudinal testing,
          Charpy V 10x10 mm test specimen
          27 J / -40 °C20 ft-lbs / -40 °F

          Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 6 mm. The specified minimum value corresponds to a full-size specimen.

          Bending Properties

          Hide/Show specific columns Edit
          Select columns to display
            Bending t < 3.00 mm 3.00 ≤ t ≤ 6.00 mm t > 6.00 mm
            Min. inner bending radius for a 90° bend 0.8 xt 1.2 xt 1.5 xt
            Compare parameters

            Select one parameter to compare

            Comparison

              Valid in both the longitudinal and transverse direction.

              Chemical Composition (ladle analysis)

              Hide/Show specific columns Edit
              Select columns to display
                C
                (max %)
                Si
                (max %)
                Mn
                (max %)
                P
                (max %)
                S
                (max %)
                Al
                (min %)
                Nb
                (max %)
                V
                (max %)
                Ti
                (max %)
                0.12 0.03 2.10 0.025 0.010 0.015 0.09 1) 0.20 1) 0.15 1)
                Compare parameters

                Select one parameter to compare

                Comparison

                  Strenx® 100 XF is available with different levels of Si: from max 0.03%, up to max 0.28%. Max Si 0.03% is the standard version that is suitable for hot dip galvanizing with thin Zinc layers, and for products that will not be galvanized. If the material is to be hot-dip galvanized and a thicker Zinc layer is requested, this must be specified at the time of order.

                  1) Sum of Nb, V and Ti = max 0.22%.

                  Tolerances

                  More details are given in SSAB’s brochure Strenx® Guarantees.

                  Thickness

                  Tolerances according to Strenx® Thickness Guarantees.

                  Strenx® Guarantees offer considerably narrower thickness tolerances compared to EN 10051. 

                  Length and Width

                  Width and length tolerances according to SSAB standard.

                  The SSAB standard offer narrower width and length tolerances compared to EN 10051.

                  Length tolerances only apply for cut to length sheets.

                  Shape

                  Tolerances according to EN 10051.

                  Narrower tolerances according to the SSAB standard are available on request 

                  Flatness

                  Tolerances according to Strenx® Flatness Guarantees Class A.

                  Strenx® Flatness Guarantees offer narrower tolerances compared to EN 10051.

                  Flatness guarantees only apply for cut to length sheets. 

                  Surface Properties

                  According to EN 10163-2 Class A, Subclass 3.

                  Delivery Conditions

                  Thermomechanically Rolled. Strenx® 100 XF is available in as rolled or pickled surface condition with mill or cut edge.

                  Fabrication and Other Recommendations

                  Welding, bending and machining

                  Strenx® 100 XF has good welding, cold forming and cutting performance. Strenx® 100 XF is a cold forming steel not suited for heat treatments at temperatures above 1080°F (580°C) since the material then may lose its guaranteed properties.

                  For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

                  Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the product.