Duroxite® 500

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    General Product Description

    Duroxite® 500 is an iron-based steel alloy overlay deposited on a mild steel backing plate. It is designed for a good combination of sliding wear and high impact applications for both dry and wet (slurry) abrasive environments. It works well at ambient or elevated temperatures up to 1100 °F (600 °C). The product is available in single and double layers.

    Duroxite® 500 consists of specially formulated abrasive materials employing a uniform glass-forming melt chemistry that allows high undercooling to be achieved. The overlay contains a unique high volume of ultra-fine chromium-niobium-rich complex borocarbide phase with a grain size refined down to 500 nm. The borocarbides are completely wetted in a ductile matrix preventing premature pull-out delamination, crack nucleation and bridging. This results in a product with significantly improved service life that maintains high toughness in sliding wear and high impact applications. Duroxite® 500 has a better combination of impact and wear resistance than those of traditional chromium carbide overlay.

    Key Benefits

    • Duroxite® 500 is mainly designed to withstand the applications involving abrasion wear and high impact.
    • Duroxite® 500 overlay contains ultra-fine complex borocarbides which is 200 times finer comparing with primary carbides in traditional chromium carbide overlay (Duroxite® 100).
    • The wear resistance of Duroxite® 500 is very similar to that of Duroxite® 100 with the weight loss in ASTM G65-procedure A, 0.18g maximum. Duroxite® 500 also maintains a consistent wear resistance from surface down to 75% of the overlay.
    • The impact resistance of Duroxite® 500 is six times better than that of Duroxite® 100 in the lab test.
    • Has uniform through-thickness hardness of 67 to 70 HRC for single and multiple-layer overlay. Maintains a high hardness of approximately 60 HRC after exposure to high temperatures up to 1100 °F (600 °C).

    Typical Applications

    Duroxite® 500 is suitable for use in the mining, power generation, cement, oil sand, steel production, waste handling, and pulp and paper industries. Some specific applications include:

    Hide/Show specific columns Edit
    Select columns to display
      Mining Earthmoving equipment, Crushing equipment, Mining equipment, Shovel buckets, Skip liners, Slurry pumps, Conveyor chains, Feeder line plate, bucket lips, hardbanding
      Cement Augers, scraper blades, muller tires, mixer tires, brick dies, tamper feet, tillage tools, chisel plows
      Oil sands Surge bins, Feed chutes, Slurry pipes, Slurry pumps
      Dredging Slurry pipes
      Power Spoon section liner plates, Ash handling equipment liners
      Agriculture Cane knives and shredders
      Compare parameters

      Select one parameter to compare

      Comparison

        Mining
        Earthmoving equipment, Crushing equipment, Mining equipment, Shovel buckets, Skip liners, Slurry pumps, Conveyor chains, Feeder line plate, bucket lips, hardbanding
        Cement
        Augers, scraper blades, muller tires, mixer tires, brick dies, tamper feet, tillage tools, chisel plows
        Oil sands
        Surge bins, Feed chutes, Slurry pipes, Slurry pumps
        Dredging
        Slurry pipes
        Power
        Spoon section liner plates, Ash handling equipment liners
        Agriculture
        Cane knives and shredders

        For more information on applications see the Duroxite® Product brochure.

        Available Dimensions

        Hide/Show specific columns Edit
        Select columns to display
          Standard overlay thicknesses
          Single pass
          Multiple Passes
          Metric unit Metric unit
          3 mm on 6 mm 6 mm on 6 mm
          6 mm on 8 mm
          6 mm on 10 mm
          6 mm on 12 mm
          Compare parameters

          Select one parameter to compare

          Comparison

            Standard overlay thicknesses

            Single pass

            Metric unit
            3 mm on 6 mm
            Standard overlay thicknesses

            Multiple Passes

            Metric unit
            6 mm on 6 mm
            Standard overlay thicknesses

            Single pass

            Metric unit
            Standard overlay thicknesses

            Multiple Passes

            Metric unit
            6 mm on 8 mm
            Standard overlay thicknesses

            Single pass

            Metric unit
            Standard overlay thicknesses

            Multiple Passes

            Metric unit
            6 mm on 10 mm
            Standard overlay thicknesses

            Single pass

            Metric unit
            Standard overlay thicknesses

            Multiple Passes

            Metric unit
            6 mm on 12 mm

            Other plate sizes and custom thicknesses can be produced upon request.

            Standard plate sizes

            Hide/Show specific columns Edit
            Select columns to display
              Metric unit Imperial unit
              1.2 m x 2.4 m 4' x 8'
              1.5 m x 3.0 m 5' x 10'
              1.8 m x 3.0 m 6' x 10'
              Compare parameters

              Select one parameter to compare

              Comparison

                Metric unit
                1.2 m x 2.4 m
                Imperial unit
                4' x 8'
                Metric unit
                1.5 m x 3.0 m
                Imperial unit
                5' x 10'
                Metric unit
                1.8 m x 3.0 m
                Imperial unit
                6' x 10'

                Other plate sizes and custom thicknesses can be produced upon request.

                Mechanical Properties

                Hide/Show specific columns Edit
                Select columns to display
                  Wear properties
                  ASTM G65 – Procedure A weight loss 2)
                  Number of overlay passes Typical surface hardness1)

                  (HRC)
                  Typical surface hardness1)

                  (HV)
                  Surface
                  (g max)
                  75 % depth of overlay 3)
                  (g max)
                  Single pass 67 - 70 925 - 1075 0.25 0.25
                  Double passes 67 - 70 925 - 1075 0.18 0.18
                  Compare parameters

                  Select one parameter to compare

                  Comparison

                    1) Surface hardness is measured on machined flat surface just below overlay surface.

                    2) ASTM G65 - Procedure A weight loss, is a standard test measuring sliding abrasion resistance using a dry sand/rubber wheel apparatus. ASTM G65-Procedure A is the most severe test method.

                    3) ASTM G65 - Procedure A weight loss, wear test is conducted at 75% depth of the overlay materials to ensure consistently good wear resistance from the top surface through to the depth of 75% of the overlay.

                    Microstructure

                    Duroxite® 500 overlay contains an ultra-fine complex borocarbide phase down to approximately 500 nm in a ductile matrix. The typical volume fraction of borocarbides is maintained between 60 to 70% to form a uniform hard matrix. The SEM (Scanning Electron Microscopy) / EDS (Energy Dispersive Spectrometry) analysis of the Duroxite® 500 overlay confirms that the refined borocarbides are niobium-rich borocarbides, and chromium-rich borocarbides dispersed in an iron-based matrix. The ultra-fine borocarbides are approximately 200 times finer than the traditional chromium carbides.

                    Tolerances

                    Thickness

                    Overall and overlay thickness tolerances can be guaranteed within ±10% of specified thickness.

                    Flatness

                    Plate flatness tolerance can be guaranteed within ±3 mm (±1/8”) over 1.5 m (5’) plate length for plate dimensions equal to or less than 1.5 m (5’) x 3.0 m (10’). For plates greater than 1.5 m (5’) wide by 3.0 m (10’) long, the plate flatness tolerance can be guaranteed within ±25 mm (±1”).

                    Delivery Conditions

                    Duroxite® 500 is supplied in an as-welded condition.

                    Fabrication and Other Recommendations

                    Welding, cutting, forming and machining

                    Recommendations can be found in the Duroxite® Product brochure, or consult your local technical support representative for more information.

                    Safety precautions

                    When welding or cutting Duroxite® products, smoke is produced containing harmful fumes and gases that are chemically highly complex and difficult to easily classify. The major toxic component in the fumes and gases produced in the process is hexavalent chromium. The proper exhaust ventilation equipment and fume-extraction torches are recommended, as well as suitable protective clothing and respiratory protection for operators.