ST100XF

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    General Product Description

    ST100XF steel plate is a low-carbon, thermo-mechanical controlled-rolled material with a guaranteed toughness that has been developed for applications where increased strength-to-weight ratios are required. ST100XF is available as temper-leveled, cut-to-length plate and meets or exceeds the requirements of ASTM A656 Grade 100.

    Applications

    ST100XF plate is designed to be used for transport trailers, construction equipment, crane booms, mobile manlifts, agriculture equipment, rail cars, heavy vehicle frames and chassis.

    Available Dimensions

    Hide/Show specific columns Edit
    Select columns to display
      Grade Product type Thickness
      (in)
      Width
      (in)
      Length
      (in)
      ST100XF Temper Leveled Plate 0.188 - 0.375 60 - 96 72 - 720
      ST100XF Temper Leveled Plate 0.375 - 0.500 60 - 72 72 - 720
      Compare parameters

      Select one parameter to compare

      Comparison

        SSAB's Cut-To-Length facilities use the temper leveled coil (TLC) process to produce temper leveled plate products. For additional information concerning our temper leveling process, please refer to our SSAB Americas: North American Cut-to-Length Operations.

        Inquire for Coils for Conversion To.

        Mechanical Properties

        Tensile testing is performed using plate-type tensile specimens in the transverse direction according to ASTM A6 requirements. The minimum requirements are tabulated below:

        Hide/Show specific columns Edit
        Select columns to display
          Product type 0.2% YS
          (ksi)
          UTS
          (ksi)
          Elongation in 2" 1)
          (min %)
          Min average energy at -40 °F
          (ft-lb) 2)
          Plate 100 110 16 20
          Compare parameters

          Select one parameter to compare

          Comparison

            NOTE: Inquire for other test specimen orientation, minimum energy requirements, and/or test temperatures.

            1) Additional elongation requirement adjustments are allowed per the Tension Test section of ASTM A6.

            2) Longitudinal specimen orientation. For sub-size CVN specimens, the minimum average energy is reduced proportionally in accordance with ASTM A673.

            Chemical Composition

            (Heat analysis, wt. %)

            Hide/Show specific columns Edit
            Select columns to display
              C
              (max %)
              Mn
              (max %)
              P
              (max %)
              S
              (max %)
              Si
              (max %)
              Al
              (max %)
              Cb
              (max %)
              V
              (max %)
              Mo
              (max %)
              N
              (max %)
              Cb+V+Ti
              (max %)
              Ti
              (max %)
              0.10 2.00 0.025 0.006 0.40 0.06 0.10 0.15 0.50 0.020 0.20 0.03
              Compare parameters

              Select one parameter to compare

              Comparison

                Carbon Equivalent

                Hide/Show specific columns Edit
                Select columns to display
                  Thickness (in) 0.188 - 0.500
                  Pcm (typ wt %) 0.21
                  Typical CEV (wt %) 0.51
                  Compare parameters

                  Select one parameter to compare

                  Comparison

                    Thickness (in)
                    Pcm (typ wt %)
                    0.188 - 0.500
                    0.21
                    Thickness (in)
                    Typical CEV (wt %)
                    0.188 - 0.500
                    0.51

                    Tolerances

                    Thickness, width, and length tolerances for ST100XF steel plate are in accordance with the requirements of ASTM A6. The flatness tolerance for as-supplied plate is ASTM A6 half-standard flatness. Procedures and tolerances for all other testing shall be in accordance with ASTM A6.

                    Formability properties

                    ST100XF exhibits cold forming characteristics similar to those of ASTM A656 Grade 80 and Grade 100. The minimum recommended punch radius, R, and the die width opening, W, as a function of bending orientation for cold bending are provided in the following table:

                    Hide/Show specific columns Edit
                    Select columns to display
                      Thickness
                      (in. [mm])
                      Bend Axis Perpendicular to Rolling Direction Inside Radius, R (min.) Bend Axis Perpendicular to Rolling Direction Die Width, W (min.) Bend Axis Parallel to Rolling Direction Inside Radius, R (min.) Bend Axis Parallel to Rolling Direction Die Width, W (min.)
                      0.188 – 0.500 1.75t 8t 2.625t 10t
                      Compare parameters

                      Select one parameter to compare

                      Comparison

                        Weldability

                        ST100XF steel plate is weldable by conventional electric arc welding processes, using low-hydrogen consumables. Although ST100XF has a chemical composition that is readily weldable without preheating or post-weld heat treatment, a precautionary preheat of 120° C (250° F) is recommended to remove any moisture. When matching consumables are not required, lower strength electrodes are recommended.

                        Hide/Show specific columns Edit
                        Select columns to display
                          Welding process Consumables
                          Shielded Metal Arc (SMAW) AWS-E11018
                          Submerged Arc (SAW) AWS F11X-EXXX
                          Gas Metal Arc (GMAW) AWS ER110S-X
                          Flux Cored Arc (FCAW) AWS E11XT-X
                          Compare parameters

                          Select one parameter to compare

                          Comparison

                            Welding process
                            Shielded Metal Arc (SMAW)
                            Consumables
                            AWS-E11018
                            Welding process
                            Submerged Arc (SAW)
                            Consumables
                            AWS F11X-EXXX
                            Welding process
                            Gas Metal Arc (GMAW)
                            Consumables
                            AWS ER110S-X
                            Welding process
                            Flux Cored Arc (FCAW)
                            Consumables
                            AWS E11XT-X