ASTM A514 Grade S

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

On this page
Show specs in Imperial Metric

General Product Description

ASTM A514 Grade S is a quenched and tempered alloy steel plate for structural applications requiring high yield strength combined with good formability and toughness. A514 Grade S has a minimum yield strength of 100 ksi [690 MPa] and may be ordered with supplemental Charpy V-notch impact test requirements.

Applications

Typical applications for A514 Grade S include transport trailers, construction equipment, crane booms, mobile man-lifts, agricultural equipment, heavy vehicle frames and chassis, and welded bridge structural members.

Available Dimensions

Hide/Show specific columns Edit
Select columns to display
    Thickness
    (inmm)
    Width
    (inmm)
    Length
    (inmm)
    0.188 - 2.004.78 - 50.8 72 - 1201800 - 3050 240 - 6006100 - 15200
    Compare parameters

    Select one parameter to compare

    Comparison

      Mechanical Properties

      Tensile Test: Tensile testing is performed in the transverse direction according to ASTM A6 requirements. The tensile property and hardness requirements are tabulated below:

      Hide/Show specific columns Edit
      Select columns to display
        UTS
        (ksi)
        Elongation in 2"
        (min %)
        Reduction of area 1)
        (min %)
        Hardness 2)
        (HBW)
        110 - 130 16 35 235 - 293
        Compare parameters

        Select one parameter to compare

        Comparison

          1) Reduction in area for 1.5 in. wide rectangular tension specimen.

          2) For plates up to 0.375 in., a Brinell hardness test may be used instead of a tensile test for those plates not tensile tested in a 15 ton lot.

          Charpy V-Notch Impact Toughness requirements may be ordered as a supplementary requirement. Please inquire for applications requiring a specified minimum impact toughness.

          Chemical Composition

          Meets chemical requirements of ASTM A514 Grade S, as shown below (wt % ladle analysis):

          Hide/Show specific columns Edit
          Select columns to display
            C
            (%)
            Mn
            (%)
            P 1)
            (max %)
            S 1)
            (max %)
            Si
            (%)
            Mo
            (%)
            V
            (max %)
            Ti
            (max %)
            Cb
            (max %)
            B
            (%)
            0.11 - 0.21 1.10 - 1.50 0.025 0.005 0.15 - 0.45 0.10 - 0.60 0.06 0.06 0.06 0.001 - 0.005
            Compare parameters

            Select one parameter to compare

            Comparison

              Inquire if a more restrictive chemistry is needed.

              1) Note that SSAB’s P and S levels are more restrictive than ASTM A514 Grade S requirements.

              Carbon Equivalent

              (wt %)
              Hide/Show specific columns Edit
              Select columns to display
                Thickness (inmm) 0.1875 - 0.7494.762 - 19.0 0.750 - 1.25019.0 - 31.75 1.251 - 2.0031.78 - 50.8
                Typical CET (%) 0.35 0.36 0.37
                Typical CEV (%) 0.48 0.53 0.56
                Compare parameters

                Select one parameter to compare

                Comparison

                  CEV and CET typical values are based on historical averages.

                  CET and CEV formula

                  Tolerances

                  Thickness, width, and length tolerances for A514 Grade S steel plate are in accordance with the requirements of ASTM A6. The flatness tolerance for as-supplied product is ½ ASTM A6.

                  Formability properties

                  ASTM A514 Grade S material exhibits good cold forming characteristics. Shear burrs and heat-affected zones of thermal cut edges on or near the bend axis as well as sharp corners on edges and on gas cut or punched holes located on or adjacent to the bend axis should be removed by grinding prior cold forming. The following recommended minimum inside bend radius, R, and die width opening, W, as a function of bending orientation are provided:

                  Hide/Show specific columns Edit
                  Select columns to display
                    Thickness
                    (in. [mm])
                    Bend Axis Perpendicular to Rolling Direction Inside Radius, R (min.) Bend Axis Perpendicular to Rolling Direction Die Width, W (min.) Bend Axis Parallel to Rolling Direction Inside Radius, R (min.) Bend Axis Parallel to Rolling Direction Die Width, W (min.)
                    0.1875 – 0.75 [4.8 – 19] 1.75t 7t 2.625t 9t
                    >0.75 – 1.00 [>19 – 25.4] 2.25t 8t 3.375t 10t
                    >1.00 – 2.00 [>25.4 – 50.8] 4.5t 12t 6.75t 16t
                    Compare parameters

                    Select one parameter to compare

                    Comparison

                      Weldability

                      Welding of A514 Grade S shall be performed in accordance with the applicable welding code. In the absence of a specified welding code, the following suggested minimum preheat and interpass temperatures and welding consumables are provided. Special welding consumables and welding procedures may be required to avoid detrimental effects on the mechanical properties of the base metal. Low hydrogen practices are strongly recommended, including the removal of surface moisture. A514 Grade S may be susceptible to reheat cracking in the heat-affected zone of welds during stress relieving or postweld heat treatment. As a result, SSAB recommends that a qualified welding engineer consider this potential before stress relieving weldments of this product.

                      Hide/Show specific columns Edit
                      Select columns to display
                        Welding process Thickness
                        (in. [mm])
                        Minimum Preheat and Interpass Temperature
                        (°F [°C])
                        Consumables
                        Shielded Metal Arc (SMAW) Up to 3/4 [19] 50 [10] AWS E10015-X, E10016-X, E10018-X, E10018-M
                        Shielded Metal Arc (SMAW) > 3/4 – 1.50 [19 –38.1] 150 [65] AWS E10015-X, E10016-X, E10018-X, E10018-M
                        Shielded Metal Arc (SMAW) >1.50 – 2.00 [>38.1 – 50.8] 200 [93] AWS E10015-X, E10016-X, E10018-X, E10018-M
                        Gas Metal Arc (GMAW) Up to 3/4 [19] 50 [10] AWS ER110S-XXX-XX
                        Gas Metal Arc (GMAW) > 3/4 – 1.50 [>19 – 38.1] 150 [65] AWS ER110S-XXX-XX
                        Gas Metal Arc (GMAW) >1.50 – 2.00 [>38.1 – 50.8] 200 [93] AWS ER110S-XXX-XX
                        Submerged Arc (SAW) Up to 3/4 [19] 50 [10] AWS F11XX-EXXX-XX, F11XX-ECXXX-XX
                        Submerged Arc (SAW) > 3/4 – 1.50 [19 –38.1] 150 [65] AWS F11XX-EXXX-XX, F11XX-ECXXX-XX
                        Submerged Arc (SAW) >1.50 – 2.00 [>38.1 – 50.8] 200 [93] AWS F11XX-EXXX-XX, F11XX-ECXXX-XX
                        Flux Cored Arc (FCAW) Up to 3/4 [19] 50 [10] AWS E11XTX-X, E11XTX-XM
                        Flux Cored Arc (FCAW) > 3/4 – 1.50 [>19 – 38.1] 150 [65] AWS E11XTX-X, E11XTX-XM
                        Flux Cored Arc (FCAW) >1.50 – 2.00 [>38.1 – 50.8] 200 [93] AWS E11XTX-X, E11XTX-XM
                        Compare parameters

                        Select one parameter to compare

                        Comparison