ST100XF

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

On this page
Show specs in Imperial Metric

General Product Description

ST100XF steel plate is a low-carbon, thermo-mechanical controlled-rolled material with a guaranteed toughness that has been developed for applications where increased strength-to-weight ratios are required. ST100XF is available as temper-leveled, cut-to-length plate and meets or exceeds the requirements of ASTM A656 Grade 100.

Applications

ST100XF plate is designed to be used for transport trailers, construction equipment, crane booms, mobile manlifts, agriculture equipment, rail cars, heavy vehicle frames and chassis.

Available Dimensions

Hide/Show specific columns Edit
Select columns to display
    Grade Product type Thickness
    (inmm)
    Width
    (inmm)
    Length
    (inmm)
    ST100XF Temper Leveled Plate 0.188 - 0.3754.78 - 9.52 60 - 961500 - 2400 72 - 7201800 - 18300
    ST100XF Temper Leveled Plate 0.375 - 0.5009.52 - 12.7 60 - 721500 - 1800 72 - 7201800 - 18300
    Compare parameters

    Select one parameter to compare

    Comparison

      SSAB's Cut-To-Length facilities use the temper leveled coil (TLC) process to produce temper leveled plate products. For additional information concerning our temper leveling process, please refer to our SSAB Americas: North American Cut-to-Length Operations.

      Inquire for Coils for Conversion To.

      Mechanical Properties

      Tensile testing is performed using plate-type tensile specimens in the transverse direction according to ASTM A6 requirements. The minimum requirements are tabulated below:

      Hide/Show specific columns Edit
      Select columns to display
        Product type UTS
        (ksi)
        Elongation in 2" 1)
        (min %)
        Min average energy at -40 °F
        (ft-lb) 2)
        Plate 110 16 20
        Compare parameters

        Select one parameter to compare

        Comparison

          NOTE: Inquire for other test specimen orientation, minimum energy requirements, and/or test temperatures.

          1) Additional elongation requirement adjustments are allowed per the Tension Test section of ASTM A6.

          2) Longitudinal specimen orientation. For sub-size CVN specimens, the minimum average energy is reduced proportionally in accordance with ASTM A673.

          Chemical Composition

          (Heat analysis, wt. %)

          Hide/Show specific columns Edit
          Select columns to display
            C
            (max %)
            Mn
            (max %)
            P
            (max %)
            S
            (max %)
            Si
            (max %)
            Al
            (max %)
            Cb
            (max %)
            V
            (max %)
            Mo
            (max %)
            N
            (max %)
            Cb+V+Ti
            (max %)
            Ti
            (max %)
            0.10 2.00 0.025 0.006 0.40 0.06 0.10 0.15 0.50 0.020 0.20 0.03
            Compare parameters

            Select one parameter to compare

            Comparison

              Carbon Equivalent

              Hide/Show specific columns Edit
              Select columns to display
                Thickness (inmm) 0.188 - 0.5004.78 - 12.7
                Pcm (typ wt %) 0.21
                Typical CEV (wt %) 0.51
                Compare parameters

                Select one parameter to compare

                Comparison

                  Thickness (inmm)
                  Pcm (typ wt %)
                  0.188 - 0.5004.78 - 12.7
                  0.21
                  Thickness (inmm)
                  Typical CEV (wt %)
                  0.188 - 0.5004.78 - 12.7
                  0.51

                  Tolerances

                  Thickness, width, and length tolerances for ST100XF steel plate are in accordance with the requirements of ASTM A6. The flatness tolerance for as-supplied plate is ASTM A6 half-standard flatness. Procedures and tolerances for all other testing shall be in accordance with ASTM A6.

                  Formability properties

                  ST100XF exhibits cold forming characteristics similar to those of ASTM A656 Grade 80 and Grade 100. The minimum recommended punch radius, R, and the die width opening, W, as a function of bending orientation for cold bending are provided in the following table:

                  Hide/Show specific columns Edit
                  Select columns to display
                    Thickness
                    (in. [mm])
                    Bend Axis Perpendicular to Rolling Direction Inside Radius, R (min.) Bend Axis Perpendicular to Rolling Direction Die Width, W (min.) Bend Axis Parallel to Rolling Direction Inside Radius, R (min.) Bend Axis Parallel to Rolling Direction Die Width, W (min.)
                    0.188 – 0.500 1.75t 8t 2.625t 10t
                    Compare parameters

                    Select one parameter to compare

                    Comparison

                      Weldability

                      ST100XF steel plate is weldable by conventional electric arc welding processes, using low-hydrogen consumables. Although ST100XF has a chemical composition that is readily weldable without preheating or post-weld heat treatment, a precautionary preheat of 120° C (250° F) is recommended to remove any moisture. When matching consumables are not required, lower strength electrodes are recommended.

                      Hide/Show specific columns Edit
                      Select columns to display
                        Welding process Consumables
                        Shielded Metal Arc (SMAW) AWS-E11018
                        Submerged Arc (SAW) AWS F11X-EXXX
                        Gas Metal Arc (GMAW) AWS ER110S-X
                        Flux Cored Arc (FCAW) AWS E11XT-X
                        Compare parameters

                        Select one parameter to compare

                        Comparison

                          Welding process
                          Shielded Metal Arc (SMAW)
                          Consumables
                          AWS-E11018
                          Welding process
                          Submerged Arc (SAW)
                          Consumables
                          AWS F11X-EXXX
                          Welding process
                          Gas Metal Arc (GMAW)
                          Consumables
                          AWS ER110S-X
                          Welding process
                          Flux Cored Arc (FCAW)
                          Consumables
                          AWS E11XT-X