SSAB Multisteel PEA
Спецификации
Спецификации
Normalized pressure vessel steel heavy plate.
SSAB Multisteel PEA is hot rolled structural steel for general pressure equipment steel constructions. PEA = Pressure European American (meets the European and American standard).
Exceeding the requirements of several standard steel grades, SSAB Multisteel PEA is a versatile pressure vessel steel for fabricated pressure equipment made of weldable fine grain steels. Formability and highly consistent quality guarantee fast, uninterrupted production, generating clear savings in the costs of material management.
SSAB Multisteel PEA exceeds several steel standards and is available as five steel grades: P355N, P355NH, P355NL1 and P355NL2 according to EN 10028-3 and SA/A516 GR 70 according to ASME/ASTM SA/A516.
SSAB Multisteel PEA covers steel grades in five different qualities:
1) Room temperature quality (P355N)
2) Elevated temperature quality (P355NH)
3) Low temperature quality (P355NL1)
4) Special low temperature quality (P355NL2)
5) General normalized pressure vessel steel with impacts (SA/A516 GR 70)
6) SSAB Multisteel PEA (all together)
PED certificate (for EN 10028-3 grades):
Pressure vessel steel grades recognized by standard EN 10028 are mainly delivered with the inspection certificate 3.1. Directive 2014/68/EU (PED) requires the manufacturer’s quality assurance system to be approved by an external accredited authority (Notified Body).
SSAB Europe Oy Raahe Works holds the PED – approval from DNV.
SSAB Raahe Works is authorized to use PED certificate for pressure equipment steels according to EN 10028-3 based on EN 10028-1.
SSAB Multisteel PEA is available in thickness of 6.00 – 50.00 mm.
The mechanical properties are tested transverse to the direction of rolling.
Hot tensile test is performed at +300°C in compliance with EN 10028-3 and EN 10028-1.
The impact test is made transverse to the rolling direction in compliance with EN 10028-3 and EN 10028-1 for European grades and longitudinal to the rolling direction in compliance with ASME SA20 for American grades.
1) Nb and V according to SA20 table 1 notes C and D.
Thickness ¾ from EN 10029 Class B.
Width and length according to EN 10029.
Flatness tolerance 6 mm/m.
Surface according to EN 10163-2 Class B subclass 3.
Normalized.
Shot blasted & primed surface is available upon request.
SSAB Multisteel PEA provides three different certificates:
EN 10204-3.1 to SSAB Multisteel PEA.
EN 10204-3.1/PED2014/68/EU to P355NL1/NL2/NH/N EN 10028-3.
EN 10204-3.1 to SA516 GR70 MTLTV.
Welding:
Weldability is excellent with all welding processes. Increased working temperature requirements are less than those of the corresponding strength grades of standard steels. This means easier welding and cost savings under both workshop and site welding conditions.
Needed working temperatures for thick plates please consult SSAB Tech Support.
Forming:
SSAB Multisteel offers better formability properties than standard steels. Successful forming requires that the manufacturer uses good workshop techniques. Worn tools, poor lubrication, scratches on the surface of the steel as well as edge burrs will all reduce forming quality.
Guaranteed minimum bending radius for all directions is 2 x t up to 30 mm thick plate where t = plate thickness.
Heat treatment:
Recommendations for stress relieving and normalizing.
Stress relieving 550 – 600°C (target 580°C)
2 minutes/millimeter of thickness, however, 30 minutes minimum. Slow cooling in the furnace.
Normalizing 900 – 940°C (target 920°C)
1 minute/millimeter of thickness, however, 20 minutes minimum. Cooling in free air.
Информацию об обработке можно найти в брошюрах SSAB на сайте www.ssab.com или связаться с технической поддержкой.
Необходимо соблюдать меры предосторожности при гибке, сварке, резке, шлифовании и других механических обработках.