Productos y servicios Marcas y productos Docol Todas las calidades de acero para automoción Aceros de aleación baja y resistencia alta Docol HR110XF

Docol HR110XF

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

Al enviar este formulario concede permiso a SSAB para procesar sus datos personas y acepta la Declaración de privacidad de SSAB. Siempre cumplimos los reglamentos locales sobre tratamiento de datos.
En esta página

    General Product Description

    Docol HR110XF cold-forming steel is a thermomechanically rolled product with a minimum yield strength of 760 MPa. Docol HR110XF is a cold forming steel for light- and heavy transport solutions and components. Docol HR110XF meets the requirements of EN 10149-2 S700MC, ASTM A1011 grade 100 and ASTM A1018 grade 100, and can be supplied according to all of these standards' specifications on request.

    Dimension Range

    Docol HR110XF is available in thicknesses of 2.0 - 10.0 mm, and in widths up to 1600 mm as coil, slit coil and as cut to length sheets in lengths up to 16000 mm.

    Mechanical Properties

    Hide/Show specific columns Edit
    Select columns to display
      Thickness
      (mmin)      		 Yield strength ReH 1)
      (min MPaksi)      		 Tensile strength Rm
      (min MPaksi)      		 Elongation A50
      (min %)
      Docol HR110XF 2.00 - 10.000.079 - 0.393 760110 813118 12
      Compare parameters

      Select one parameter to compare

      Comparison

        The mechanical properties are tested in the transverse direction.

        Testing is also performed in the longitudinal direction, according to requirements in EN 10149-2 S700MC and ASTM A1011 grade 100.

        1) If ReH is not applicable then Rp0.2 is used.

        Impact Properties

        Hide/Show specific columns Edit
        Select columns to display
          Product Min. impact energy for longitudinal testing,
          Charpy V 10x10 mm test specimen
          Docol HR110XF 27 J / -40 °C20 ft-lbs / -40 °F
          Compare parameters

          Select one parameter to compare

          Comparison

            Product
            Docol HR110XF
            Min. impact energy for longitudinal testing,
            Charpy V 10x10 mm test specimen
            27 J / -40 °C20 ft-lbs / -40 °F

            Bending Properties

            Hide/Show specific columns Edit
            Select columns to display
              Bending t < 3.48 mm 3.48 ≤ t ≤ 6.00 mm t > 6.00 mm
              Min. inner bending radius for a 90° bend 0.8 xt 1.2 xt 1.6 xt
              Compare parameters

              Select one parameter to compare

              Comparison

                Valid in both the longitudinal and transverse direction.

                Chemical Composition (ladle analysis)

                Hide/Show specific columns Edit
                Select columns to display
                  C
                  (max %)                  		 Si
                  (max %)                  		 Mn
                  (max %)                  		 P
                  (max %)                  		 S
                  (max %)                  		 Al
                  (%)                  		 Ti
                  (max %)                  		 Nb
                  (max %)                  		 V
                  (max %)
                  Docol HR110XF 0.12 0.03 2.10 0.025 0.010 0.015 0.15 1) 0.09 1) 0.20 1)
                  Compare parameters

                  Select one parameter to compare

                  Comparison

                    Docol HR110XF is available with different levels of Si: from max 0.03%, up to max 0.28%. Max Si 0.03% is the standard version that is suitable for hot dip galvanizing with thin Zinc layers, and for products that will not be galvanized. If the material is to be hot-dip galvanized and a thicker Zinc layer is requested, this must be specified at the time of order.

                    1) The sum of Nb, V and Ti is max 0.22%.

                    Tolerances

                    Thickness

                    Tolerances according to 1/2 of EN 10051 category D.

                    Length and Width

                    Tolerances according to EN 10051.

                    Shape

                    Tolerances according to EN 10051.

                    Flatness

                    Tolerance 3mm/m which only apply for cut to length sheets.

                    Surface Properties

                    According to EN 10163-2 Class A, Subclass 3.

                    Delivery Conditions

                    Thermomechanically Rolled. Docol HR110XF is available in as rolled or pickled surface condition with mill or cut edge.

                    Fabrication and Other Recommendations

                    Welding, bending and machining

                    Docol HR110XF has good welding, cold forming and cutting performance. Docol HR110XF is a cold forming steel not suited for heat treatments at temperatures above 580°C since the material then may lose its guaranteed properties.

                    For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

                    Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.

                    Contact Information

                    www.ssab.com/contact