SSAB Weathering 460ML

Download data sheet

Select Language

Get datasheet by email
Close

Get datasheet by email

    General Product Description

    SSAB Weathering 460ML steel grade is thermomechanically rolled structural steel offering a good weather resistance. This steel has excellent usability properties. Its surface quality, dimensional accuracy and the consistency of its properties are among the best on the market. Thanks to its good properties, these steels promote environmentally sound construction and sustainable development.

    SSAB Weathering 460ML brings clear performance benefits for heavy steel structures like bridges. Thanks to the excellent resistance to atmospheric corrosion, there is no need for the additional coatings, such as painting of steel structures. Therefore, a significant cost advantage can be achieved in applications, where a dark brown patina is desired on the steel surface. However, the steel surface can be shot blasted and painted, using the same methods as when painting ordinary steel grades. As a result of the special alloying of the steel, the lifespan of the painting is about double that of an ordinary steel grade painted.

    The anti-corrosion properties of SSAB Weathering 460ML are much better than those of the ordinary structural steels which are commonly used in many outdoor applications. The enhanced weather resistance is based on the oxide layer, i.e. patina. The elegantly brown patinated surface is architecturally distinguished. Patina starts to be yellowish first and when the time goes on the color will turn to darker brown.

    SSAB Weathering 460ML meets or exceeds the requirements of S460J5W+M in EN 10025-5. Upon agreement, they can be delivered dual certified.

    Dimension Range

    SSAB Weathering 460ML is available in thickness 8.0 - 65.0 mm.

    Mechanical Properties

    Hide/Show specific columns Edit
    Select columns to display
      Thickness
      (mm)
      Yield strength ReH
      (min MPa)
      Tensile strength Rm
      (MPa)
      Elongation A5
      (min %)
      8.00 - 16.00 460 530 - 710 15
      16.01 - 40.00 440 530 - 710 15
      40.01 - 63.00 430 530 - 710 14
      63.01 - 65.00 410 530 - 710 13
      Compare parameters

      Select one parameter to compare

      Comparison

        The tensile test is made transverse to the rolling direction in compliance with EN 10025-1 and EN 10025-5.

        Certificates:

        SSAB Weathering 460ML provides two different certificates:

        EN 10204-3.1 to SSAB Weathering 460ML and S460J5W+M.

        Impact Properties

        Hide/Show specific columns Edit
        Select columns to display
          Grade Min. impact energy for longitudinal testing,
          Charpy V 10x10 mm test specimens
          SSAB Weathering 460ML 27 J / -50 °C
          Compare parameters

          Select one parameter to compare

          Comparison

            Grade
            SSAB Weathering 460ML
            Min. impact energy for longitudinal testing,
            Charpy V 10x10 mm test specimens
            27 J / -50 °C
            The impact test is made longitudinally to the rolling direction in compliance with EN 10025-1 and EN 10025-5.

            Chemical Composition (heat analysis)

            Hide/Show specific columns Edit
            Select columns to display
              C
              (max %)
              Si
              (max %)
              Mn
              (max %)
              P
              (max %)
              S
              (max %)
              Cu
              (max %)
              Cr
              (max %)
              Ni
              (max %)
              0.12 0.65 1.40 0.015 0.005 0.55 0.80 0.50
              Compare parameters

              Select one parameter to compare

              Comparison

                Carbon Equivalent

                Hide/Show specific columns Edit
                Select columns to display
                  Thickness (mm) 8.00 - 65.00
                  Typical CEV (%) 0.43
                  CEV (max %) 0.48
                  Compare parameters

                  Select one parameter to compare

                  Comparison

                    Thickness (mm)
                    Typical CEV (%)
                    8.00 - 65.00
                    0.43
                    Thickness (mm)
                    CEV (max %)
                    8.00 - 65.00
                    0.48
                    CET and CEV formula

                    Tolerances

                    Thickness ¾ from EN 10029 Class A. Width and length according to EN 10029.

                    Flatness 6 mm/m.

                    Surface according to EN 10163-2 Class A subclass 3.

                    Delivery Conditions

                    Thermomechanically rolled (M).

                    Possible to order as shot blasted & primed.

                    Fabrication and Other Recommendations

                    Welding:

                    The weldability of SSAB Weathering ML steel is excellent. Thermomechanically processed steels have good resistance to hydrogen cracking and reduced need for preheating. All conventional welding methods can be used. If the welded structure shall be made according to the standard EN 1090-2 rules, the selection of acceptable welding consumables shall follow the standard EN 1090-2.

                    The recommended preheating temperature depends on the CEV carbon equivalent of the base material and the welding consumables, applied heat input (Q), hydrogen content of the welding consumables (HD) and the combined thickness of the welded joint configuration (mm) according to the standard EN 1011-2 (method A).

                    Choosing low hydrogen content welding consumables (HD ≤ 5 ml / 100 g) will minimize the risk of hydrogen cracking and reduce the need for preheating. SSAB Weathering ML steels have relatively low CEV values. According to the standard EN 1011-2 method A, in most cases, preheating is not required when low hydrogen content welding consumables are used and the welding heat input Q ≥ 1,5 kJ/mm.

                    When welding is performed with the high hydrogen content welding consumables (5 ≤ HD ≤ 10 ml / 100g) and with the heat input Q < 2,5 kJ/mm, the preheating is recommended. In most cases, the preheating is not required even with high hydrogen content welding consumables if the welding heat input Q ≥ 2,5 kJ/mm.

                    However with very thick plates (single plate thickness ≥ 40 mm), it is always helpful to use minimum preheating +100…125°C because of the high stresses that can be encountered in such structures. Preheating is also recommended when using very low heat input Q < 1,0 kJ/mm (e.g. root pass of the weld or tack welds). For low heat inputs < 1.0 kJ/mm preheating shall be determined according to the standard EN 1011-2, method A.

                    Preheating recommendations for SSAB Weathering 355ML, 420ML and 460 ML. HD= diffusible hydrogen content of welding consumable (ml/100 g) and Q = welding heat input (kJ/mm). For low heat inputs < 1.0 kJ/mm preheating shall be determined according to the standard EN 1011-2, method A. With very thick plates (single plate thickness ≥ 40 mm) it is however always helpful to use preheating +100…125°C.

                     

                     

                    Forming up to 20 mm:
                    Minimum inner bending radius 2 x t can be used in both longitudinal and transverse direction in 90 degree three-point bending. Minimum die-width is recommended to be at least 10 x t. Close attention should be paid on the cut edges in the bend area and all excessive cracks or burrs should be removed. It is also important to be sure that the plate surface is defect free (no scratches) on the deformation area before bending.


                    Surface:
                    In order to achieve even good looking patina layer scale removal is recommended. That can be done either with pickling or shot blasting.

                    For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.

                    Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.

                    Contact Information

                    www.ssab.com/contact