SSAB Opti™ Cut Plate

Download data sheet

General Product Description

SSAB Opti™ Cut is structural quality steel specifically designed to enhance laser cutting performance. SSAB Opti™ Cut meets and exceeds the requirements of the relevant ASTM and Canadian Standards Association (CSA) specifications. Dual and multiple certifications to ASTM A36, A572-50, A656-50 and CSA G40.21 38W, 44W and 50W specifications are avaiable upon request.

Available Dimensions

Product type
Product type
Hot-Rolled Plate
Thickness
(inmm)
0.500 - 1.500 1)12.7 - 38.10 1)
Width 3)
(inmm)
60 - 1201500 - 3050
Length 4)
(inmm)
240 - 4806100 - 12200
Product type
Product type
Hot-Rolled Plate
Thickness
(inmm)
1.501 - 2.000 2)38.13 - 50.80 2)
Width 3)
(inmm)
60 - 1201500 - 3050
Length 4)
(inmm)
240 - 4806100 - 12200

1) Standard thicknesses 5/8 in., 3/4", 1.0 in., 1.25 in., and 1.50 in. Please inquire for non-standard thicknesses.

2) Standard thicknesses 1-3/4" and 2 in. Please inquire for non-standard thicknesses.

3) Standard widths 60 in., 72 in., 96 in., and 120 in. Please inquire for non-standard widths.

4) Standard lengths 240 in. and 480 in. Please inquire for non-standard lengths.

Mechanical Properties

Tensile Properties:  Tensile testing is performed in the transverse direction according to ASTM A6 requirements.

Thickness
(inmm)
Thickness
(inmm)
0.500 - 1.50012.7 - 38.10
Yield strength
(min ksi)
50
Tensile strength
(ksi)
65 - 80
Elongation in 2" 2)
(min %)
21
Elongation in 8" 2)
(min %)
18
Min. inner bending radius for a 90° bend
Perpendicular / Parallel
1.5 x t / 2.25 x t
Thickness
(inmm)
Thickness
(inmm)
1.501 - 2.00038.13 - 50.80
Yield strength
(min ksi)
50
Tensile strength
(ksi)
60 1)
Elongation in 2" 2)
(min %)
21
Elongation in 8" 2)
(min %)
18
Min. inner bending radius for a 90° bend
Perpendicular / Parallel
1.5 x t / 2.25 x t

1) Single value represents minimum tensile strength requirement.

2) Elongation requirements for plates wider than 24 in.

Impact Properties

Grade
Grade
SSAB OptiTM Cut
Min. impact energy for longitudinal testing,
Charpy V 0.393x0.393" test specimen
20 ft-lbs / -22 °F

Charpy V-notch impact testing performed with longitudinal specimens in accordance with ASTM 673, H frequency.

Chemical Composition

Thickness (inmm)
Thickness (inmm)
0.500 - 1.50012.7 - 38.10
C
(max wt %)
0.18
Mn
(wt %)
1.35 1)
P
(max wt %)
0.020
S
(max wt %)
0.01
Si
(max wt %)
0.10
CE 2)
(max wt %)
0.45
Thickness (inmm)
Thickness (inmm)
1.501 - 2.00038.13 - 50.80
C
(max wt %)
0.18
Mn
(wt %)
1.35
P
(max wt %)
0.020
S
(max wt %)
0.01
Si
(max wt %)
0.10
CE 2)
(max wt %)
0.50

1) For each reduction of 0.01 percentage point below 0.25% C, an increase of 0.06 percentage point manganese above 1.20% is permitted up to a maximum of 1.35%.

2) Carbon Equivalent (CE) = C +Mn/6 + (Cr+Mo+V)/5 + (Cu+Ni)/15

Tolerances

SSAB Opti™ Cut cut-to-length plates are produced to 1/2 of the ASTM A6 permitted variation over the specified thickness and to the restrictive plate flatness requirements of ASTM A6.  Width and length tolerances for SSAB Opti™ Cut are in accordance with ASTM A6.

Fabrication and Other Recommendations

SSAB Opti™ Cut plates have been optimized for laser cutting, cold forming and welding. For information concerning fabrication, see SSAB's brochures on www.ssab.com or consult Tech Support. Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products. Contact information www.ssab.com

Contact Information

www.ssab.com/contact