180
Duroxite 500
Duroxite

 

DUROXITE®  500

YOUR SOLUTION FOR WEAR AND HIGH IMPACT



Duroxite®  500 is the latest addition to the range of Duroxite® overlay products. It is designed for applications involving abrasive wear and high impact in dry and wet environments. Duroxite® 500 can replace cast materials, titanium carbide overlay products or ceramic materials.

 
Duroxite(R) Formula

Ultra-fine complex borocarbides stand up to impact

Duroxite® 500 overlay contains complex borocarbides that are 200 times finer than chromium carbides. The complex borocarbides prevent spalling and cracking when exposed to high impact.
Duroxite(R) longer life

3 times longer wear life in copper mine

When replacing the cast Mn liner plate with Duroxite® 500 in the belt machine head, wear life increased from 15 to 45 days. 2,700,000 tons of copper ore was processed before maintenance compared to 900,000 tons for the cast liner.
Duroxite(R) hardness at high temperature

High hardness also at high temperature

Duroxite® 500 has a uniform through-thickness hardness of 67 to 70 HRC for single and multiple-layer overlays. It maintains a high hardness of approximately 60 HRC after exposure to temperatures up to 600°C (1100 °F).
SSAB Duroxite 500 Uptimers

We are able to extend your wearparts lifetime with Duroxite® 500

Duroxite® 500

Duroxite® 500

Standard overlay thicknesses

 Standard plate sizes

 Single pass

 Multiple passes

 

 Metric unit

Imperial unit 

 Metric unit

 Imperial unit

 Metric unit

 Imperial unit

 3 mm on 6 mm  1/8’’ on 1/4’’  6 mm on 6 mm  1/4’’ on 1/4’’  1.2 m x 2.4 m
1.5 m x 3.0 m
1.8 m x 3.0 m
2.4 m x 3.0 m
 4’ x 8’
5’ x 10’
6’ x 10’
8’ x 10’
 5 mm on 8 mm  3/16’’ on 5/16’’  6 mm on 10 mm  1/4’’ on 3/8’’
     10 mm on 10 mm  3/8’’ on 3/8’’
     12 mm on 12 mm  1/2’’ on 1/2’’
     20 mm on 10 mm  3/4’’ on 3/8’’

Surface Hardness

Number of overlay passes 

Typical surface hardness 1) 

 Single and double passes  67 to 70 HRC (925 to 1075 HV)

 

1) Surface hardness is measured on machined flat surface just below overlay surface.

 

Wear Properties

 

Number of overlay passes 

ASTM G65 – Procedure A weight loss 2) 

 

 Surface

75% depth of overlay 3) 

 Single pass  0.25 g maximum  0.25 g maximum
 Double passes  0.18 g maximum  0.18 g maximum

 

2) ASTM G65 is a standard test measuring sliding abrasion resistance using a dry sand/rubber wheel apparatus. ASTM G65-Procedure A is the most severe test method.
3) ASTM G65 wear test is conducted at 75% depth of the overlay materials to ensure consistently good wear resistance from the top surface through
to the depth of 75% of the overlay.


Duroxite® 500 overlay contains an ultra-fine complex borocarbide phase down to approximately 500 nm in a ductile matrix. The typical volume fraction of borocarbides is maintained between 60 to 70% to form a uni-form hard matrix. The SEM (Scanning Electron Microscopy) / EDS (Energy Dispersive Spectrometry) analysis of the Duroxite® 500 overlay confirms that the refined borocarbides are niobium-rich borocarbides, and chromium-rich boro carbides dispersed in an iron-based matrix. The ultra-fine borocarbides are approximately 200 times finer than the traditional chromium carbides.


Thickness

Overall and overlay thickness tolerances can be guaranteed within ±10% of specified thickness.

Flatness

Plate flatness tolerance can be guaranteed within ±3 mm (±1/8”) over 1.5 m (5’) plate length for plate dimensions equal to or less than 1.5 m (5’) x 3.0 m (10’). For plates greater than 1.5 m (5’) wide by 3.0 m (10’) long, the plate flatness tolerance can be guaranteed within ±25 mm (±1”).

Duroxite® 500 is supplied in an as-welded condition.

Welding, cutting, forming and machining

Recommendations can be found in the Duroxite® Product brochure, or consult your local technical support representative for more information.